Jump to content

1944 Jaeger Lecoultre Mark Vii Raf Pilot Watch

stvn66

By stvn66
in Your Watch Collection

 Share

Recommended Posts

WillFly Distinguished Member

WillFly

Posted
Posted

Welcome to the forum - BUT, Senior Member's privileges mean that I'm going to have to take that from you...

 

You see, Jaeger LeCoultre is one of my favourite makes, may Dad was in the RAF - and my birth year is 1944...

 

Sorry about that - I'll PM you me address. :D

Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted

Thanks, I suppose it is a good starting point for a research. I'm not familiar with timex at all from the watchmaking stand point that is. I've heard they are difficult to work on so I guess it would be a challenge I'm looking forward to tackle. I like the design so if I could restore one I will feel very proud wearing it!

 

Just learning one baby step at a time!

 

Cheers,

 

Bob

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Murks
      Battery

      By Murks · Posted

      A don't think so it leaked or damaged it because the watch itself works it just the buttons ain't working not connecting with the circuit board have taken more pictures of where the buttons makes contact with the circuit board.
    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      I think what peter means oh is once he has fitted the hands and  checked for  alignment if them and that they dont foul, how does he then hold the movement to remove the stem in order to case up. The dial cannot be laid on a cushion or in a movement holder as the hands will get damaged. This can be quite tricky for a beginner, what i do is  to stand the movement on edge on a rubber pad so it doesn't slip. Hold the top edge with one finger then my dominant hand uses 3 fingers to press the stem release and flick out the stem. See below peter, leave off the second hand as this is the longest and gets caught the most, then fit it once the stem is out. Alternatively place the movement in one of the cup style holders, i imagine this is what they are designed for. They only touch the very edge of the dial.  
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      Yes I understand that. What I’m asking is, after the hands have been fitted, it’s been checked that the hands do not touch etc. then I need to remove the stem to fit the movement in the case. I have the push type, I need to turn it upside down and push the setting lever post and pull the stem out. But of course the dial and hands are in place and I have a glossy dial with lume dots and I do not want to cause any damage while it’s upside down pushing on the post of the setting lever.
    • oldhippy
      Stem removal after fitting hands

      By oldhippy · Posted

      You have answered your own question. You just push the setting lever nipple in or if its the screw in type unscrew it a little. You should always remove any hands and the dial before putting it in your movement holder. 
    • HectorLooi
      Battery

      By HectorLooi · Posted

      Did the old battery leak and damaged the circuit board? Can you post some photos of where the buttons make contact on the circuit board.  Try cleaning the gold fingers on the board with alcohol and also the conductive rubber strips behind the LCD display panel.
×
×
  • Create New...