Jump to content

New Watch Cases

Legarm
 Share

Recommended Posts

  • Replies 115
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Fissile
Fissile

The reason there are more old movements available than old cases is because many of those old cases were made of gold or silver.  When bullion prices were high a gold or silver cased watch was worth m

Posted Images

WillFly Distinguished Member

WillFly

Posted
Posted (edited)

It's a real problem. Very few watch parts suppliers deal in cases other than for the fairly standard ETA 6497/8 ex-pocket watch movements (Hamilton, Panerai, etc.). I have a lovely Longines 280 movement  for which I've been trawling for a case for a long time - with no luck. I keep checking eBay for watches with duff movements but, in most cases, a duff movement is housed in a duff case!

 

I have one case for which I have no movement. I'd be happy to send it to you to see if it fits one of your movements - with no obligation if it doesn't...

Edited by WillFly
Link to comment
Share on other sites
Legarm WRT Addict

Legarm

Posted
  • Author
Posted

It's a real problem. Very few watch parts suppliers deal in cases other than for the fairly standard ETA 6497/8 ex-pocket watch movements (Hamilton, Panerai, etc.). I have a lovely Longines 280 movement  for which I've been trawling for a case for a long time - with no luck. I keep checking eBay for watches with duff movements but, in most cases, a duff movement is housed in a duff case!

 

I have one case for which I have no movement. I'd be happy to send it to you to see if it fits one of your movements - with no obligation if it doesn't...

 

Thanks Will .... all very true.

 

I would like to take up your kind offer, at least let me pay the postage....... :)

 

I shall PM you my address.......

Keith

Link to comment
Share on other sites
WillFly Distinguished Member

WillFly

Posted
Posted

Oh, I remember that one. All the way from Italy if my memory serves me, nice case though!

Spot on, Geo - as I recall, it was you who drew my attention to it in the first instance. It's a lovely case, just not quite right for the 280 calibre. And I just can't find the calibre that it will fit. Sod's law!

Link to comment
Share on other sites
  • 3 months later...
Gary Super WRT Addict

Gary

Posted
Posted

Hi All! 

 

So I have been successful in getting an old Bulova 11AFC back to work. The dial is horrible and hands were very rusty but I cleaned it as well as I could. The movement was very clean and went back together easily. I am going to post photos later. I may have the dial restored and some new hands but not sure it is worth all that.

 

On another note. I purchased the three of the watches listed in the photo. Looking for suggestions on cases and casing alternatives?

 

Any thoughts or suggestions are welcomed.

 

Thanks,

Gary

post-337-0-98864100-1423871296_thumb.jpg

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

Hi Gary, it's a big ask to find the correct cases for these movements, the chances of finding the correct ones is not great. If you are skilled enough and keen enough and have the equipment, you could get something close and machine to fit.

Being realistic, it is probably better just to use them for practicing on, and buy a complete watch that is in need of total refurbishment, that way you will have all the parts at minimum cost. :)

Link to comment
Share on other sites
WillFly Distinguished Member

WillFly

Posted
Posted

Geo's absolutely spot on here - the right cases are a bugger to find and, as we all know, most movements for sale are the result of the silver or gold cases being sold for scrap. I've been trying to find a case for my Longines 280 for a long time now - with no luck.

 

I know a watch casemaker who did some work on one of my Elgin railroad watches a couple of years ago. I contacted him to price up making a case for the Longines in stainless steel. £2,500. Mmm...

 

The irony is I have a case for a Longines cal. 30L - and can't find a movement for it! :pulling-hair-out:

Link to comment
Share on other sites
vaguras Member

vaguras

Posted
Posted (edited)

There are 3 30Ls on the Bay at the moment - but they're either too expensive or not in good condition for the price.

 

My 280 movement is in beautiful condition - and cost me less than £50.

Will, have you already seen this one ?

http://www.ebay.com/itm/LONGINES-30L-original-mechanic-watch-movement-running-1351-/261711540602?pt=ES_Relojes_de_pulsera&hash=item3cef39317a

Edited by vaguras
  • Like 1
Link to comment
Share on other sites
Gary Super WRT Addict

Gary

Posted
Posted

Thank you for the thoughts and no loss they were intended to be practice movements. That said, I have mangled heat another mainspring on the one I really liked with the silver dial. Seems my weak areas are mainsprings, hair springs and keyless works.

On a good note the Girrard Perregeaux has been disassembled and oiled lightly and back together. In a 24 hour period though it is running a little fast, about a minute. A.)I'm grateful I put another one back together, yeah! B.) with little experience I'm not sure where to look for this fault. Any suggestions would be greatly appreciated?

Gary

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

with little experience I'm not sure where to look for this fault. Any suggestions would be greatly appreciated?

Gary

Hi Gary, what fault are you referring to? If it's the "minute a day fast", you should be able to correct that by adjusting the regulator.

Link to comment
Share on other sites
Gary Super WRT Addict

Gary

Posted
Posted

Geo- I will use the regulator to adjust. Is it normal to have to adjust the regulator? After a correct service should it have to be adjusted? My thought is the middle would be the optimal position? Is that unrealistic of a watch this age?

 

Thanks!

 

Gary

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

Hi Gary, when you purchase old watches you never know who has been at them. A lot of folk will tamper with the regulator to try and compensate for the watch behaving badly, when it should really get a full service. The bottom line is after a service it policy to check the rate and adjust as required.

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted (edited)

Could this be something that fits the round movements  ? it's a nice stainless steel case . The diameter of the movement needs to be 26,5 or under . And from the dial to the center of the stem 1,7 mm . Have about 17 mm lugs . The crystal is a little yellow from age but that isn't a big expensive thing to replace . Yours if you want ?  Or someone else ?? 

 

post-644-0-71196200-1424184521_thumb.jpgpost-644-0-98606500-1424184545_thumb.jpg

Edited by rogart63
Link to comment
Share on other sites
  • 3 weeks later...
Vich Distinguished Member

Vich

Posted
Posted

May be worth a trip to the watch fairs there are often big boxes full of broken watches and sometimes you get lucky. Another thing is looking at "steampunk" stuff. It is amazing what people are selling just for decoration. The only other place is of course the Bay. There is also a place on this forum to advertise for specific stuff.

Good luck,

Vic

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • mthomas828
      Balance staff sourcing?

      By mthomas828 · Posted

      Hello, I am about 5 months into watchmaking and I love it!   The attention to precise detail is what really attracts me to it. (and the tools!) I am working on a 16 jewel 43mm pocket watch movement.   There are no markings besides a serial number (122248) .  The balance staff needs replacement. The roller side pivot broke off.  I successfully removed the hairspring using Bergeon 5430's.  I successfully removed the roller using Bergeon 2810.   Did i mention I love the tools?! I removed the staff from the balance wheel using a vintage K&D staff removal tool  with my Bergeon 15285 (that's the one that comes with a micrometer adjustment so it can be used as a jewel press as well as a traditional staking tool...it's sooooo cool...sorry..  can you tell i love the tools?) No more digressing..  I measured the damaged staff in all the relevant areas but I have to estimate on some because one of the pivots is missing. A = Full length  A= 4.80mm  (that's without the one pivot...if you assume that the missing pivot is the same length as the other pivot (I'm sure it's not)  then A = 5.12 mm...(can I assume 5.00mm here?) F=  Hair spring collet seat  F=  .89mm   (safe to assume .90 here? .. I am sure that my measurement's would at least contain  .01 mm error ?) G = balance wheel seat  G = 1.23 mm  (1.20mm?) H  =  roller staff  H =  .59mm  (.60 mm?) B  = bottom of the wheel to roller pivot   B  = 2.97mm  (3.00 mm?)     here I am estimating  again because this pivot is missing. So my friends, and I thank you profusely,  can you point me in the right direction as to how to proceed? Do i buy individual staffs?  or an assortment?   Since I don't know exactly the name of the manufacturer, will that be a fatal hindrance?   Tbh, I'm not even sure what country of origin this movement is. Thank you!    
    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      Thats why i asked that question earlier, what happens if lubrication is placed directly on top of epilame ?  As opposed to walled within its non epilamed area . I'm not saying its right, i have no idea , just asking questions. 
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      thinking of where epilam should be removed did you know there was a patent that covers this? At least for the escapement I'm attaching it. GB1057607A-1 epilame.pdf
    • LittleWatchShop
      Movement holder made with 3D printer

      By LittleWatchShop · Posted

      Back home...printing now.  Will report results
    • VWatchie
      Epilame / Fixodrop

      By VWatchie · Posted

      Oh well, if Master @nickelsilver says it's the way to go, then it is the way to go! I stand corrected! 🫡 Are there any other places where you're supposed to remove the epilame from the contact point of rubbing? I don't think so! Thanks for the effort @Neverenoughwatches, much appreciated! 🙂👍
×
×
  • Create New...