Jump to content

Recommended Posts

Posted

have just got one of these waterproof russian watches, it has a bezel on it a anchor on the dial.

Does anyone know where I can get a replacement  screw down Crown, as the one that is on the watch the spring has gone on it, and it just flops around when its unscrewed. 

The picture isn't the exact watch, but it's near enough. 

Thanks

$_35.jpeg

Posted

I think you need to check it is actually broken first. Vostok Amfibia use a rather clever clutch so the crown is only engaged with the movement when changing the time. They are meant to wobble around like they are broken.


Sent from my iPad using Tapatalk Pro

  • Like 3
Posted

Check if it's actually broken first.  If it is you could find a new one on Ebay. There are sellers that sell new crowns . Be careful when changing the crown and stem as the keyless works is easy to mess up. Press down and pull out. 

  • Like 1
Posted

+1 @rogart63 and @Sopgeo.

This is a design characteristic of the Amphibia and also the most common query / concern of newbie Amphibia owners.

Just google Vostok Amphibia wobbly crown and you will find many examples as below;

http://forums.watchuseek.com/f10/question-about-boctok-amphibia-crown-wobble-462400.html

Somewhere on the net there is a really interesting article about the development and evolution of the Amphibia design which explains a lot of its idiosycracies, if I can find it again I will post a link.

These are actually great watches and represent truly excellent value for money.

  • Like 1
Posted

Yes it's a nice watch, most of the ones I've seen on ebay the plating doesn't survive well.

Anyway I dicided ide see if I could fix it,  so I pulled out the stem, found a spring that fitted inside the pendant tube and just lot enough to reach the crown and bobs your uncle, no more wobbly crown .

Posted

I have just got one of these waterproof russian watches, it has a bezel on it a anchor on the dial.

Does anyone know where I can get a replacement  screw down Crown, as the one that is on the watch the spring has gone on it, and it just flops around when its unscrewed. 

The picture isn't the exact watch, but it's near enough. 

Thanks

5a113087dd2a7__35.jpeg.a167a27923f1a5f33f11f529531502c2.jpeg
Have you tried CousinsUK?

Sent from my SM-G935F using Tapatalk

  • 7 months later...
Posted
On ‎2017‎-‎11‎-‎19 at 2:00 PM, Marc said:

This is worth a read if you want a better understanding of Amphibias;

http://forums.watchuseek.com/f54/vostok-amphibia-analysis-design-methodology-491757.html

1

Later, someone used this write-up as a script to record a video, and this video sparked my passion for Russian watches. The design, at the time, was truly something new and special, and it still holds water (pun intended)!

 



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hmm, if it is sitting that low I am not sure I would blame end shake (which would be to blame if you turned it DU and the hairspring touched the balance cock). If it is sitting so low that the balance rubs on the pallet bridge I would verify that the balance arms are not dished downward and also that the lower balance jewel doesn't have an issue such as being chipped. Or the balance staff is actually too short, which would have caused your earlier end shake problems too. If you install the pallet bridge without the pallet fork and install the balance, is your free oscillation still good or is it immediately bound up on the pallet bridge? (I have an elgin watch like that where someone in the past ground down the pallet bridge significantly) Yes, you'll need to rotate the hairspring but deal with the pallet bridge interference first.
    • Ok. So given that I had free oscillations DU/DD for roughly the same time, I reassembled with the pallet fork and bridge underneath, and now I can see two more problems.    1. The arms of the balance are nearly flush with the pallet bridge. Bad. I can speculate as to why…the end shake still looks to be too much. Maybe other causes as well? 2. The balance doesn’t spin freely. In the resting position, it looks like the impulse jewel is outside the jaws of the pallet fork. Not by much, but still outside. If it needs be inside in the static position, then I’m guessing I’ll need to rotate my hairspring collet to change orientation by a few degrees.    The journey continues…
    • Ok, that's good to know, thank you.
    • Andy, why you betray me?   I may have good news. I'll share later!
    • Hi. I have been touching watches for quite some years, but haven’t before pretty recently decided to jump of the cliff by trying to do basic service for the first time. It is a simple Seiko 6602 I bought as a renovation movement.  To be honest I struggled. Mainly because I wanted to do everything correctly and with all the right tools etc from the start.  From just having basic tools I invested in quite a lot of things in order to dissemble, clean and lubricate the movement parts. I can say it was a journey.  Taking care of the balance jewels looks really easy watching all the great videos, but god damn… I have been lucky and only shot away things that was found but come on. Anyway. I have now managed to “service” four movements and the result is what makes me want to keep doing this.    The first movement was a Seiko 6602 and it was in a pretty bad shape. When I run it on the Timegraoher now I got an amplitude of 270 and in all positions it stays around +-2s.    I have heard some “amateurs” saying this is a hobby you’ll get stuck to and I am already there. It doesn’t matter if it’s a fancy movement or a simple 6602. The feeling after been struggling and you see the result… it’s amazing! I am still in a state where I am confused and don’t know which watch press tool is best, or if I need the most fancy hand tools etc, but to be honest. This is so stimulating.    Sorry for not really adding anything new to you all pros. 
×
×
  • Create New...