Jump to content

Seagull movements

Alaskamick

By Alaskamick
in Watch Repairs Help & Advice

 Share

Recommended Posts

Alaskamick WRT Addict

Alaskamick

Posted
Posted

I have previously assembled a few watches for friends using ETA movements ending up with nice looking watches which work as required.

What is the opinion of the knowlegable people here of Seagull movements?

Does anyone have personal stories, horror or good, based on the usage of seagull, not just hearsay.

Am I going down the wrong route using cheaper movements?

I would be grateful for any advice from your experiences.

Thanks, Mike

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

I recently acquired a Chinese chronograph wristwatch with a Seagull TY 2903 movement.  The finish on the movement is excellent it is keeping 2 - 3 seconds a day. The complete watch new was £129, a Swiss watch with the same specification would cost many thousands of pound.  Do I like it..........no.........I love it!

Here is a photo of the graph with daily rate.

 

IMG_3824.PNG

  • Like 1
Link to comment
Share on other sites
RyMoeller Super WRT Addict

RyMoeller

Posted
Posted

Nice Chrono Geo. 

Alpha makes some very attractive homage pieces using the ST19 movement which is manufactured using the same tooling Venus used for the 175.  I don't think you can find a better deal for a mechanical chronograph and the movement is tried and true. :)

  • Thanks 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • noirrac1j
      Rolex 2235 escape wheel jewel setting replacement

      By noirrac1j · Posted

      Hell0 @nevenbekriev. Thank you for your advice. I have removed the old setting using my staking set--I will keep the KIF spring, since it is still good.  I am awaiting the replacement setting, and will update when I do that. In the mean time, I looked at the escape wheel and it looks ok. What do you think?    
    • Hawaiikook808
      Seitz Tool - Help determine if Seitz or not

      By Hawaiikook808 · Posted

      Aloha All, I recently bought this Seitz tool on eBay, but it is missing some pushers reamers.  I ended up ordering new parts for those that were missing before I received the actual Seitz tool (bad idea).   Upon inspecting the pushers/bits, I noticed 23 of the 56 provided with the set had no numbers. Further inspection revealed a huge difference in the quality of those unnumbered.  Do all Seitz pushers/bits have a number on them?  I'm pretty sure that 33 of the 56 I received are cheap Chinese knockoffs.  The worst part is that I ordered $80 of parts to replace the missing pushers/bits, and now I'm looking to return the tool. I'm not crazy, right? If these are Seitz parts, they should all be numbered, correct? The first two pictures are the Seitz (numbered), and the other pictures are the suspect parts.  Will I even be able to get a refund?  Thanks, Frank     
    • luiazazrambo
      WWW Eterna sucked me in.

      By luiazazrambo · Posted

      It was £10 + min fee, total £16, could not leave it there. Its a Stanton A.D.2. http://stanton-instruments.co.uk/
    • Geotex
      Generic screws for unknown movements

      By Geotex · Posted

      Chief- The picture below shows the three parts from the dial side that are most useful to "fingerprint" a movement in conjunction with the diameter of the movement.  That's why forum participants are always asking for dial side photos in posts asking for identification.  As far as the setting lever screw, it actually sits loose in the main plate. The threads engage the setting lever below, and the elongated stem above the shoulder sticks through a hole in one of the bridge plates so that it's held captive if unscrewed all the way.  So you may be fine as far as that goes. 
    • Chief
      Generic screws for unknown movements

      By Chief · Posted

      So I found what I believe is the setting lever screw! Am I right in thinking the screw next to the click is the correct one for the setting lever? However if it is, it doesn't fit in the hole which I believe is for it! I can get the lever to sit nicely on the stem and line up with a hole, but the screw only goes as far as the shoulder and stops. It's as though the hole is too small! The dial side has been disassembled by the way, the other wheels are in my tray
×
×
  • Create New...