Jump to content

Screeching sound when winding a bumper automatic

Stian

By Stian
in Watch Repairs Help & Advice

 Share

Recommended Posts

Stian WRT Addict

Stian

Posted
Posted

Hi guys, 

A bumper automatic I bought makes a screeching sound when I wind it. A little bit the same sound as a regular rotor automatic, but sharper and more metallic, if that makes sense. Have you come across something like this? 

Could the spring be rotating the wrong way inside the barrel, thereby making this sound? 

--

Thanks, 

Stian 

Link to comment
Share on other sites
Vich Distinguished Member

Vich

Posted
Posted

I think OH put his finger on it, I had this once with an old watch from the bay and it was quite literally completely dried out inside. Service it and check the spring out.

Cheers,

Vic

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Dell
      What is the correct way to lubricate clock mainsprings?

      By Dell · Posted

      Surely it depends on the clock , I only usually restore torsion clocks and I only use oil on mainspring ( small amount) but on the few so called normal pendulum clocks I have done I have used mainspring grease as there is more reserves of power than there is in a torsion clock so it is not so critical. Dell
    • Delgetti
      Venus 178 hour counter creep

      By Delgetti · Posted

      https://watchguy.co.uk/cgi-bin/files?showfile=Venus/Venus 178.pdf&filename=Venus 178.pdf&dir=Technical Manuals&action=documents   The hour recorder is driven by the barrel and it will only stop if it is held by the hour recorder stop lever 8690. So I would check if this lever (powered by the spring 8691) is really holding the hour recorder in the "chrono off status". I haven't worked on a Venus 178 so far, but on an Omega 861 I chose 9501 grease for the friction spring as it's moving very slow at quite high tension.
    • Waggy
      Can someone please explain watchmaker service mark interpretation?

      By Waggy · Posted

      All I do is use a fine marker (sharpie) to put the service date on the back cover, this way it can be removed with some IPA and does no permanent damage to the watch. I'm in two minds about the whole service marking thing, sometimes it's good/bad to see the markings on the watch case back as you know it's been worked on and vice versa. However, if I took my car in for a service and the mechanic scratched some code into the housing of my engine I wouldn't be too impressed. Hence, I think my sharpie solution is a reasonable compromise.
    • Waggy
      Movement holder made with 3D printer

      By Waggy · Posted

      hmmmm.... maybe there is a way to skin that cat 🙀 let me think on it... unless anyone else has any ideas? I left the opening in the side of the base and ring quite large to maybe allow you to grip the crown, but appreciate this may not always be possible, especially for small movements where the crown will not extend past the outer wall of the holder. I noticed this also, but after using the holder for a while I noticed that the ring/holder began to wear into shape (rough edges/bumps worn off) and the size became closer to the desired movement OD. Maybe with some trial and error we could add 0.5 mm (??) to the movement OD to allow for this initial bedding-in?
    • Mallard
      Vintage pocket watches from e-bay (winding stems needed)

      By Mallard · Posted

      Hi nickelsilver, thanks for the great explanation and the links! I'll take a good look in the article.  Especially this is great news to hear! Looking through forums and youtube videos I was informed to 'fist find a case and then fit a movement for it'. But seems that's not the case for pocket watches at least?  I guess I should be looking to find some 'male square bench keys' for now. I was thinking of winding the mainspring using a screwdriver directly, but I found a thread that you've replied on, saying that it could damage the spring. 
×
×
  • Create New...