Jump to content

Girard Perregaux 03BG repaired lugs and refinished case

noirrac1j

By noirrac1j
in Your Watch Collection

 Share

Recommended Posts

noirrac1j Distinguished Member

noirrac1j

Posted
Posted (edited)

Hello everyone,

Just satisfied my degree requirements last week, so have a little bit of time to post. Don't know how many of you run into watchcases that have worn or broken lugs....I had a Girard Perregaux watch case with the lug holes so worn I was afraid to wear it--there was just a thin band of metal left on the lug. I sent it away for plugging and redrilling of lugs plus refinishing. Very good job! This movement (GP 03bg, adjusted) has a nice looking star decoration over the non-shock protected balance jewel. I have not seen one like it before. 

J

GP 03BG 607.pdf

Edited by noirrac1j
  • Like 1
noirrac1j Distinguished Member

noirrac1j

Posted
  • Author
Posted
4 minutes ago, dadistic said:

Well, congratulations on getting to the finish line with school!

Nice watch, too.

Thank you! Yes it was quite an investment in time and energy, but one that is well worth it. The GP's have a vintage look and great quality without the premium that similar Omega and Longines watches command.

J

  • Like 1
  • 1 month later...
ricardopalamino Distinguished Member

ricardopalamino

Posted
Posted

Congratulations Joe . 

Nice watch . I definitely like it .  With running the risk of being nosey . can you give  the details on the refinish ,...where , time it took , and cost ?  I have a case or two that I have thought about doing the same to .  PM me if you prefer...

Thanks , Louis

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Michael20
      French drum novice

      By Michael20 · Posted

      Regarding the spring winders, I made my own and used copper pipe reducers as the tubes to retain the spring. You will need to cut out a section for the end of the spring to protrude but if you watch one of the many videos on this subject that will make sense. You can find a selection of sizes on Ebay for very little cost. I'll attach a pic showing one of mine.  Good luck!
    • JohnR725
      Omega sweep second pinion friction spring - correct tension IS important

      By JohnR725 · Posted

      There were things bothering me about this discussion that took me a while to figure out the problem. In the image below it appears to be the spring may be pushing up? Normally when Omega has a spring pushing up the pinion has a pivot with a bridge to hold it in place so in other words the spring can push on something that stationary as opposed to this which appears to be floating? To understand the problem with the above image we need another image of side view which I have below. In my image down below on the left-hand side it agrees with the image up above. But the only problem is the left-hand side is defective and the right-hand side image is the way it's supposed to look. Then Omega if you can access the right documents does explain how and why this problem occurs. With the pinion floating around it might be assumed that you support it when putting on all the hands but you do not because as noted below if you do this small bush on the pinion will relocate out of position exactly what we see in the image up above.   Then Omega does not mention this but there is a possibility of also damaging the pinion and causing the bush to move to where it's not supposed to be when removing the hands.   
    • LittleWatchShop
      Regulating is too touchy

      By LittleWatchShop · Posted

      Maybe show us 1) the watch, 2) timegrapher readings in DU, DD, PU, and PD.
    • Louis1969
      Regulating is too touchy

      By Louis1969 · Posted

      The timegrapher displays significant beat error variations in the dial-up position. When the watch is lying flat (face up), the beat error is much higher than in other positions. Beat error readings are inconsistent, with especially large gaps in the face-up position.  Please help !  
    • Geotex
      Informational universe.

      By Geotex · Posted

      Looks like an open-access journal that runs as a glorified pre-print server with no true peer review, so it’s not easy to judge the veracity of the conclusions.
×
×
  • Create New...