Jump to content

Sekonda Stem Came Out When Adjusting Time

ro63rto

By ro63rto
in Watch Repairs Help & Advice

 Share

Recommended Posts

ro63rto Distinguished Member

ro63rto

Posted
Posted

My brother had the battery changed in Goldsmiths about a month ago. Doubt they caused this but I'm miffed at the damage to the caseback.

Anyhoo, when my brother pulled out the crown to adjust the time today, the whole stem came out.

My tool kit doesn't have a case tool with a thin enough blade to open it. While I order one, does the stem look worn/damaged (still adjusts time & date) if not, what do I need to re-seat it?

Thanks, Rob.

IMG_20140720_143032.jpg

IMG_20140720_143104.jpg

IMG_20140720_143123.jpg

IMG_20140720_22134801.jpg

Link to comment
Share on other sites
ro63rto Distinguished Member

ro63rto

Posted
  • Author
Posted

If the case was pristine to begin with that damage is shocking. At least with it being stainless steel, you can re-finish it quite easily.

First battery change in its life and bought new.

Will refinish after if I can fix it for him.

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

Why can't I find a case knife with a thin enough blade to open this?

Get one of these, they have a narrow width at the tip and you get a lot of leverage and control. I have used one for a long time now with great success.

http://www.ebay.co.uk/itm/Watch-Back-Case-Knife-Opener-Remover-Watchmaker-Jeweler-DIY-Repair-Tool-Orange-/231269195527?pt=UK_Jewellery_Watches_WatchAccessories_SpareParts_SM&hash=item35d8b7df07

Link to comment
Share on other sites
ro63rto Distinguished Member

ro63rto

Posted
  • Author
Posted

Hey Geo, how thick is that tip as I have a similar one and its too thick for this particular case back.

The only thing I have is an old razor sharp 2" lock knife and no way am I using that. Probably end up in hospital, again. :wacko:

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

Well done. If you ave a look at the area where the stem goes into the movement. There will either be a small button or a lever press, I don't think it will be held by a screw. I have not worked on one of these, so I may be wrong.

Link to comment
Share on other sites
ro63rto Distinguished Member

ro63rto

Posted
  • Author
Posted

Found it using loupe. Just above the H of "Push" is a hole. Under it a lever appears when stem is all the way in.

I think either the part that holds the stem or the collar on the stem itself must be worn out.

Movement is Time module SII VD57B. Will try and find a pic of replacement stem and compare it.

Link to comment
Share on other sites
Lee WRT Addict

Lee

Posted
Posted (edited)

there's nount wrong with the stem, I would suspect that whoever butchered the case back, then merrily prized the old battery out with a screw driver & bent the top plate dislodging the stem lock.

post-138-0-70884500-1406301519_thumb.jpg

the area circled in red looks to be damaged/scratched to me???? if so then this is probably where they tried to push things together again

 

I would start by giving the area cirled in black a little push down. OR take it back armed with what I've said & get them to replace the movement at their cost!

 

Lee

Edited by Lee
Link to comment
Share on other sites
Lee WRT Addict

Lee

Posted
Posted

Now don't get me wrong I could be way off base & totally incorrect but what I see in the picture & your fault, suggests to me..............

 

There's a little clip that releases the battery bridge "A" I'd lay money down they haven't used it, instead stuck a screw driver in somewhere in the area of "B" and forced the battery out causing the top plate to be damaged, which by pushing back down they've thought they got away with!

post-138-0-45588600-1406302909_thumb.jpg

Link to comment
Share on other sites
ro63rto Distinguished Member

ro63rto

Posted
  • Author
Posted

I bow to your waaaaaay greater knowledge, expertise etc.

I'll speak to my brother and see what he wants to do. He may ask me to try to remedy as per your suggestion but I want his go ahead.

It was about a month back that he had the battery changed. Wish I had checked the caseback before and after while infront of the assistant. :angry:

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • luiazazrambo
      404 Club

      By luiazazrambo · Posted

      There is one Oris there at least, and if you could get a Unicorn for this price!??! 😄 It says that they don't work though, you might need to figure out what a Unicorn eats then. 😉 
    • luiazazrambo
      Which Watch Have You Got Coming In The Mail ? Show Us !!!

      By luiazazrambo · Posted

      I wonder whats inside, bought it blindly, not cheap at all.
    • Jon
      Rolex Cal 1570 Balance wheel rubbing

      By Jon · Posted

      Here's a quick Gif I made to show truing the balance using callipers. This has such a slight wobble, but is within acceptable parameters. The important thing is the balance doesn't touch or rub anything when in operation. This is an Eterna Tank. Here's a pic of the balance freshly rivetted with a new staff in the movement
    • spectre6000
      404 Club

      By spectre6000 · Posted

      I just poked an inflation calculator, and $5 in 2020 would be about $6 in 2024. Doesn't fit very neatly into any status codes, which stop at 5XX, but that's honestly somewhat arbitrary outside of a clever pun for those that dabble in such things. Back during the pandemic, I would spend a good chunk of idle time in the evenings scanning through hundreds of listings a night, and I would only land 1-2 a week max. I would often go months without finding something suitable. A very small percentage of the watches in the price range are worth pulling the trigger on for my purposes. The number floating through the thread here may be somewhat deceptive.
    • Zedster
      Balance cock stud screw

      By Zedster · Posted

      Hi, guys I got there in the end after several attempts using a screwdriver and Rodico, I couldn't wait for the tool to arrive and was getting pretty confident handling the stud screw without it flying away. At first, I was using far too much Rodico, and then realized you only need the smallest amount inside the screw slot. Putting the cock back onto the movement also helped as it gave me more to hold onto while my shaky hand tried to align the screw wobbling away at the end of the screwdriver😁 Anyway, job done and I can move on. Thanks again for all the advice it's really appreciated for a beginner. 
×
×
  • Create New...