Jump to content

Bulova Jet Clipper.....


ricardopalamino

Recommended Posts

I recently acquired this really nice Bulova Jet Clipper....

DSC00001.JPG

DSC00006.JPG

Screen shot 2016-12-25 at 12.23.27 AM.png

Screen shot 2016-12-25 at 12.32.16 AM.png

 

As I said , It was nice but needed a little TLC . It was advertised as running good , just cleaned and serviced . Also It came on a period Spiedel watchband and had a decent crystal .

Unfortunately it would only run for a bit , and needed an inspection and service . It's a front loader , so after pulling off the crown and the top of the 2 piece stem , and the crystal , I got a better look at what I had . The dial is a beautiful scallop sea shell design that has a soft pearlesent sheen,...subtle on the pearlesent . The lume on the hands was starting to fall off , and all three hands had signs of rust present . 

The movement had some dirty lube in the stem area but the rest of the movement was in top shape . I proceeded to clean and service the movement and was pleased to see good results on my timegrapher .

I removed the lume and the rust from the hands , cleaned and polished them , and relumed the hour and minute hand  . I also sanded and polished the crystal , but it didn't take much to make it look like new . I like the little spade arrow on the short side of the second hand .

I found a decent beads of rice bracelet in my stash and the watch was looking and running good . 

 

DSC00007.JPG

 

As good as it was looking to me , I wanted to up the ante . In my searches I had come across a vintage Spiedel Calendar watchband called Romunda by Spiedel . It is stainless steel and has leather looking links . The calendar has 7 faces that moves the 1st from Sunday to Saturday by rolling the calendar backwards or forward with 2 setting wheels . The calendar cost $10.95 when it was first introduced ,...I paid $25.00 ,....but had to have it for this watch .

 

Screen shot 2016-12-25 at 12.16.20 AM.png

Screen shot 2016-12-25 at 12.17.01 AM.png

 

The lug width on the watch is 18mm , and the watchband is 19mm , so I had to do some body and fender work to make it fit . Also the band was too loose on my wrist so I had to remove 2 sets of links to fit me . That was fun .

 

DSC00012.JPG

 

All in all , I am very pleased with the total look of the watch and band . I think it looks pretty darned spiffy . 

Like something from "Mad Men " .

 

DSC00015.JPG

DSC00016.JPG

DSC00014.JPG

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  • Like 3
Link to comment
Share on other sites

Excellent Ricardo. I just did an 333ft Oceanographer with black/ gold cross hairs dial. I really liked the beads of rice bracelet until I saw how good the calendar stretch band looked! I would not have made that choice, but it really does look as good as any Omega of that time. Very clean looking....its nice to see esthetics being given priority rather just focusing on the mechanical aspects. Of course timegrapher readings, smoothly functioning features and original hardware are important believe me I know this very well. But in the end, when all the work is done, the watch just has to look and feel "right" on the wrist. Otherwise, whats the point of wearing a timepiece? Any 10 dollar watch could serve that purpose.... but not for us!

JC

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Surely it depends on the clock , I only usually restore torsion clocks and I only use oil on mainspring ( small amount) but on the few so called normal pendulum clocks I have done I have used mainspring grease as there is more reserves of power than there is in a torsion clock so it is not so critical. Dell
    • https://watchguy.co.uk/cgi-bin/files?showfile=Venus/Venus 178.pdf&filename=Venus 178.pdf&dir=Technical Manuals&action=documents   The hour recorder is driven by the barrel and it will only stop if it is held by the hour recorder stop lever 8690. So I would check if this lever (powered by the spring 8691) is really holding the hour recorder in the "chrono off status". I haven't worked on a Venus 178 so far, but on an Omega 861 I chose 9501 grease for the friction spring as it's moving very slow at quite high tension.
    • All I do is use a fine marker (sharpie) to put the service date on the back cover, this way it can be removed with some IPA and does no permanent damage to the watch. I'm in two minds about the whole service marking thing, sometimes it's good/bad to see the markings on the watch case back as you know it's been worked on and vice versa. However, if I took my car in for a service and the mechanic scratched some code into the housing of my engine I wouldn't be too impressed. Hence, I think my sharpie solution is a reasonable compromise.
    • hmmmm.... maybe there is a way to skin that cat 🙀 let me think on it... unless anyone else has any ideas? I left the opening in the side of the base and ring quite large to maybe allow you to grip the crown, but appreciate this may not always be possible, especially for small movements where the crown will not extend past the outer wall of the holder. I noticed this also, but after using the holder for a while I noticed that the ring/holder began to wear into shape (rough edges/bumps worn off) and the size became closer to the desired movement OD. Maybe with some trial and error we could add 0.5 mm (??) to the movement OD to allow for this initial bedding-in?
    • Hi nickelsilver, thanks for the great explanation and the links! I'll take a good look in the article.  Especially this is great news to hear! Looking through forums and youtube videos I was informed to 'fist find a case and then fit a movement for it'. But seems that's not the case for pocket watches at least?  I guess I should be looking to find some 'male square bench keys' for now. I was thinking of winding the mainspring using a screwdriver directly, but I found a thread that you've replied on, saying that it could damage the spring. 
×
×
  • Create New...