Jump to content

Fuel prices

clockboy
 Share

Recommended Posts

clockboy Distinguished Member

clockboy

Posted
Posted

I have just driven from Italy through 5 countries getting back to the UK today.  It never stops to amaze me the variants in prices of car fuel. The differences are caused by the amount of tax the various counties seem it fair to levy. The cheapest is without doubt Luxenberg (see pic) the prices shown are in €,s & diesel converts to approx 65p per litre.

 

fuel.jpg

 

 

 

Link to comment
Share on other sites
stroppy WRT Addict

stroppy

Posted
Posted

Suburban Melbourne (AU) today:

(Prices in Aussie dollars.  One AUD = .77c US)

Standard unleaded (91RON-what most cars use here) = $1.09 per litre

E10 (ten percent ethanol at 95RON) = $1.00 per litre (Late model cars run without issue on E10 but the fuel is less dense so consumption is higher)

95RON = $1.18 per litre            98or100RON = $1.22 per litre

LPG = .65c per litre (lots of locally made cars run on LPG, especially taxis)  

Diesel = $1.06 per litre                 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Pallet jewel

      By Neverenoughwatches · Posted

      The entry and exit stones have different impulse face angles  murks.
    • Waggy
      First Project Already A Bit "Sideways"

      By Waggy · Posted

      Depending on how much of the screw is left, you may be able to screw it further in and it may fall out of the hole that the dial foot sat in. To do this I rough up the tip of the good screw and screw it in, often the rough surface of the good screw and the rough surface on the broken screw get enough of a bite to transmit the torque into the broken section and force it out the other side. Like I said the size of the broken screw needs to be in your favor, but you never know you may get lucky.... or if you get it moving you may be able to then back it out with a screwdriver taking a bite on the rough surface. worth a try
    • DDean
      First Project Already A Bit "Sideways"

      By DDean · Posted

      I will try this weekend.  I've tried several times with my cell phone and it's just too small and recessed to get a good picture.  I need to get my macro lens and tripod out and then figure out how to get enough light down the hole in the side of the man plate to  actually show the top of the broken screw. I appreciate the effort and will try and get that pic this weekend.
    • RichardHarris123
      Simeon from Down Under

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • Simeon
      Simeon from Down Under

      By Simeon · Posted

      Hi,   My name is Simeon I am based in Sydney, Australia and have recently got into watch repair / watch making.  I am very much a learner having serviced multiple forgotten watches, some of which were actually successful!   I have a slowly growing collection of watches, mainly old Soviet, a few Japanese and (not pictured) some Raketas, a Poljot Alarm, an Omega Speedmaster Reduced and a vintage (1972) Tissot Seastar.  I like unloved vintage watches, with quirky faces and enjoy bringing them back to life through the simple(!) act of disassembly, clearing and reassembly. I am an Electrical Engineer who also undertook a trade apprenticeship so I am reasonably handy - It's fair to say, I know just enough to get myself in trouble. 
×
×
  • Create New...