Jump to content

These brass tools have conical ends of various sizes...???

LittleWatchShop
 Share

Recommended Posts

JohnR725 Distinguished Member

JohnR725

Posted
Posted
8 hours ago, oldhippy said:

They look home made turned down from brass rod.

8 hours ago, LittleWatchShop said:

A highly skilled machinist could do that, but they are all very close in design.  I do not believe they are homemade.

probably factory made but they could also be made by students in watchmaking schools. Often times for lathe projects stuff like this would be made.

Then yes they are the jewel pushing tools for pushing out balance jewels.

for instance here's an example of what the Elgin College was having the students make. At the bottom are the jewel pushers I just gave you the whole page

image.thumb.png.c58b04b780d878db64edb221299c7b0f.png

 

  • Like 1
  • Thanks 1
Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted
4 hours ago, JohnR725 said:

probably factory made but they could also be made by students in watchmaking schools. Often times for lathe projects stuff like this would be made.

Then yes they are the jewel pushing tools for pushing out balance jewels.

for instance here's an example of what the Elgin College was having the students make. At the bottom are the jewel pushers I just gave you the whole page

image.thumb.png.c58b04b780d878db64edb221299c7b0f.png

 

Is there anything you do not know?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Bonefixer
      Oily Oris

      By Bonefixer · Posted

      Thought I had to share this - last time I cleaned out a deep fat fryer there was less mess than this. Another pin pallet movement. Unsurprisingly dunking it in Castrol GTX didn't fix the broken mainspring which is the only issue I've found.    Any tips for the dial? Also covered in oil.  Cleaned up quite nicely
    • Neverenoughwatches
      AS 554 from 1930

      By Neverenoughwatches · Posted

      Hi Nev . No i didn't try this balance in the movement as it didn't run and the deformed staff broke when i removed the roller. Problem is what i think is the correct staff for this movement, the hub seat, roller and collet profiles are all too small for those parts of the assembly. The movement listed on Ranfft's site is correct my movement and the nos staffs i have match the ronda measurements. I can only assume that the wheel , roller and collet openings have all been broached to make them fit an oversized staff, both staff pivots had also been modified. 
    • pent
      B-Dip residue?

      By pent · Posted

      Yes, threw it on the demagnetizer before I cleaned it to be sure.  This picture doesn't show it well, but I can definitely see liquid where the turns meet up.
    • GuyMontag
      404 Club

      By GuyMontag · Posted

      My newest 404 candidate, a late '60's / early '70's Waltham with a UTC 33 / Seiko 6601 17 jewel automatic movement. It needed a new crystal and I put on a strap from my Strap Graveyard. The timegrapher was a snow storm before servicing but it cleaned up nicely. I really like the funky font used for the hour markers.
    • nevenbekriev
      AS 554 from 1930

      By nevenbekriev · Posted

      Hi Rich, the main problem with the balance is if the roller is from this movement. Did Yoy try if the balance interacted correctly with the lever? You can use suitable (by size) balance/hairspring couple from You pile of balances, but the roller must be for this lever (original for the calibre). Not that making roller is impossible, but it is easier to have one.
×
×
  • Create New...