Jump to content

Introduction to site

eltel

By eltel
in Introduce Yourself Here

 Share

Recommended Posts

eltel New Member

eltel

Posted
Posted

Hi, Terry here from Darkest Devon.

Just recently started looking at watches as a hobby, starting on fairly simple problems. managed to destroy a couple of cheapies. Howeve a so called friend has asked me to replace a broken stem and crown for him.  I thought this would not be too bad but i cannot even work out how to get the movement out of the case. Thewatch is a Cortina DS-1 automatic and looking inside it appears to me that there is a cover over what would be the exposed part of the stem so I cannot get at it(see photo). does this mean it is beyond my capabilities as it would mean a strip down or am I missing something. I wuld be grateful for any advice.

IMG_20230423_091207511.jpg

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi. When you look at the stem where it fits into the watch you will notice a small key hole push a probe into the hole to find the stem release and with tweezers at the same time pull back the stem.     You will also notice (rh side) a stickler shaped clip there will be another opposite to release the movement once the clamps have been removed…. Move the rotor and have a look under the balance for a makers mark and calibre number, there may be a tech/parts sheet available at cousins uk. Document downloads.

Link to comment
Share on other sites
eltel New Member

eltel

Posted
  • Author
Posted

Have tried pushing the release button. There is no sign of any movement.  Being new to this, every stem I have seen is a screw thread right down to the movement. This one does not have this and seems to be solid. The movement is 2825-2.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Pallet jewel

      By Neverenoughwatches · Posted

      The entry and exit stones have different impulse face angles  murks.
    • Waggy
      First Project Already A Bit "Sideways"

      By Waggy · Posted

      Depending on how much of the screw is left, you may be able to screw it further in and it may fall out of the hole that the dial foot sat in. To do this I rough up the tip of the good screw and screw it in, often the rough surface of the good screw and the rough surface on the broken screw get enough of a bite to transmit the torque into the broken section and force it out the other side. Like I said the size of the broken screw needs to be in your favor, but you never know you may get lucky.... or if you get it moving you may be able to then back it out with a screwdriver taking a bite on the rough surface. worth a try
    • DDean
      First Project Already A Bit "Sideways"

      By DDean · Posted

      I will try this weekend.  I've tried several times with my cell phone and it's just too small and recessed to get a good picture.  I need to get my macro lens and tripod out and then figure out how to get enough light down the hole in the side of the man plate to  actually show the top of the broken screw. I appreciate the effort and will try and get that pic this weekend.
    • RichardHarris123
      Simeon from Down Under

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • Simeon
      Simeon from Down Under

      By Simeon · Posted

      Hi,   My name is Simeon I am based in Sydney, Australia and have recently got into watch repair / watch making.  I am very much a learner having serviced multiple forgotten watches, some of which were actually successful!   I have a slowly growing collection of watches, mainly old Soviet, a few Japanese and (not pictured) some Raketas, a Poljot Alarm, an Omega Speedmaster Reduced and a vintage (1972) Tissot Seastar.  I like unloved vintage watches, with quirky faces and enjoy bringing them back to life through the simple(!) act of disassembly, clearing and reassembly. I am an Electrical Engineer who also undertook a trade apprenticeship so I am reasonably handy - It's fair to say, I know just enough to get myself in trouble. 
×
×
  • Create New...