Jump to content

Latest Purchase


Recommended Posts

This being my first post may I say a big hello to everyone, i joined in May and would like to apologise for not greeting you sooner. My main interest is in pocket watches and hope to show you some of my collection over the next few weeks.Today i would like to show you a couple of cleaning machines purchased recently,they came as one lot, can you guess what they cost!

 

1. A  B.H T  as soon as i got it back home i checked the electrics out these being o.k. i powered it up and all seemed fine apart from a couple of issues someone may enlighten me on, the rotary switch which controls the speed only functions from position 2 to 7 and the heater comes on at no.5, i have a sneaky feeling that the rotary switch has been changed, what do you think? Sorry about the first picture i did rotate it on my computer but do not know why it has gone back

 

post-1002-0-06144700-1437768035_thumb.jppost-1002-0-89479900-1437768066_thumb.jppost-1002-0-93376400-1437768120_thumb.jppost-1002-0-28012500-1437768151_thumb.jppost-1002-0-91108300-1437768191_thumb.jp

 

2. A National Major. The electric wiring needs replacing but after checking with my multimeter that no shorts were showing i powered it up. 

    and it works great, in some respects it seems better than the BTH in as much as a rheostat controls the speed and the heater can be switched on independently, it also has a mechanical Smiths timer fitted. Are the glass jars still available?

post-1002-0-17210100-1437768667_thumb.jppost-1002-0-13728800-1437768691_thumb.jppost-1002-0-73514800-1437768713_thumb.jp Sorry about the first picture.

 

If you have any information on them or not please let me know what you think.Regards and thanks for taking the time to read this post.John.

Link to comment
Share on other sites

Hi Atki! (Sorry! Blame Jennings!)

Good finds there. Maybe the problem with the BHT is a mucky or corroded rheostat surface. If you can access the innards you should see a slightly brighter track where the contact moves over the coil. If it's dull after the 7 position it may be possible to carefully clean the coil to improve conduction but it might also suggest that it wasn't normally used at a higher setting. Maybe 7 was enough.

As for the jars, Cousins has them - https://www.cousinsuk.com/product/tornado-90-accessories- but without lids! For 25 quid I'd expect a lid!

I'd take a few measurements and trot down to the supermarket with a ruler and see what you can find on the shelves. The lid needs to be plastic to resist corrosion but why shouldn't the jar also be plastic?

Good hunting.

(another) John :)

Link to comment
Share on other sites

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I used to just remove the stem pop the movement in its case then put the stem back in check everything then back on the timer. 
    • That's the right technique Mal 👍 If you are ok with a loupe ( which I'm not ) then pick up the dial in your left hand and make a tripod holder out of 3 fingers and then exactly how Mal and me described with your right hand, press and flick out the stem at the same time. You need three fingers to do this, i use my ring ring finger , sounds like mal uses his little finger, just whatever you feel comfortable with. The key point and dangerous side to this is the tweezers or driver slipping off the release screw. Stablise your left arm by resting your elbow on your bench, so that you can hold the movement horizontally flat, use a x5 loupe to view  and good light so you can see well and have a good tight fitting screwdriver to push the release down. Or as suggested a pusher mounted solid upside-down somewhere then all you need to do is push your movement up to it. I'll rig something up in a bit to show you what i mean. Something like this, but tbh its better to just learn to do with your fingers.
    • Thanks Michael, shes a real soldier, it would take a tank to knock her off her feet.  Shes surprised even me and i knew she was a tough cookie.  Good for you Michael, you keep at it. I've been reading your posts re. your watchroom they're inspiring and it doesn't matter how long it takes you to get there its about the journey. Rome wasn't built in a day, our watchcaves are our solitudes, our own little empires where we can shut ourselves away from the crap that goes on around us in the world. I look forward to seeing you progress, I have my own ideas how i like to do things. But in answer to your questions on that thread, just let your workspace evolve around you and how you work. You wont figure it out straight away but you will know when to change it and when to leave it alone. But most of all just enjoy it.
    • That can be tricky. Sometimes I hold the movement from the edges in left hand and with right hand I push the release with tweezers and simultaneously pull the stem out with right hand pinky or something. 
    • I see what you mean. I must admit I’m not entirely comfortable with that but I can’t see a better method than what you suggest. I’d like to see something like this mirror with a short spike: https://www.cousinsuk.com/product/mirror-for-observing-movements Place it on, push the spike on the post with one hand and release the stem with the other hand. Minor problem, it doesn’t exist.
×
×
  • Create New...