Jump to content

Recommended Posts

Hello

Firstly let me apologize in advance for asking the same question that a lot of other people (myself included) have already asked.  I have a Bergeon Mainspring Winding Kit and I want to use it to re-install a mainspring correctly. I've provide two pictures; One with the lid off the barrel showing the mainspring and arbor and the second picture is of the arbor only. If I understand it corectly, then I want to wind the mainspring using the blue dot (left-hand / counterclockwise) winding arbor?

Thanks in advance for any help that can be provided.

Barrel - Bottom of Arbour Facing Up.jpg

Arbour Hook.jpg

Link to comment
Share on other sites

24 minutes ago, mcoulton said:

Hello

Firstly let me apologize in advance for asking the same question that a lot of other people (myself included) have already asked.  I have a Bergeon Mainspring Winding Kit and I want to use it to re-install a mainspring correctly. I've provide two pictures; One with the lid off the barrel showing the mainspring and arbor and the second picture is of the arbor only. If I understand it corectly, then I want to wind the mainspring using the blue dot (left-hand / counterclockwise) winding arbor?

Thanks in advance for any help that can be provided.

Barrel - Bottom of Arbour Facing Up.jpg

Arbour Hook.jpg

Your spring will only wind one way for obvious reasons, but it could be installed upside down in the wrong handed winder. Looking in the winder at the spring it will be the reverse of how it was in the barrel. To  simplify things imagine looking at the spring through the top of the winder, this will be the same orientation it was in the barrel. Good to take pictures or make a drawing showing which way the spring spirals in the barrel before removing. Not the end of the world if you dont as the arbor hook wil point you in the right direction also depending on the type of spring tail a barrel wall ledge will indicate spring direction.

Link to comment
Share on other sites

This is considered a right-hand wound spring because looking at it in the barrel, the spring coils to the right, or clockwise.

I originally thought the same way as you--if the arbor winds counter-clockwise, it must be a left-hand spring. This Esslinger blog post finally clarified it for me (emphasis mine):

Quote

Before you begin winding your mainspring you first need to tell if it needs to be wound clockwise or counter-clockwise. Most mainsprings are wound clockwise (spirals from the center to the right) – you can see this when you open the barrel and look down into the mainspring while it’s still in the barrel. There are some mainsprings that are wound counter-clockwise and this is why Bergeon makes “right” and “left” handed winding arbors. They are specified by a red (right-hand) or blue (left-hand) dot.

 

Link to comment
Share on other sites

Thanks very much for the help. 

Neverenoughwatches - I did your trick and looked down the winder from the plunger end - not the arbor winding end - and that naturally orientates the hook with the hook on the arbor that came out of the barrel.

ManSkirtBrew - Thanks for the Esslinger article. I'll make a note of it and add in my comments. 

 

  • Like 1
Link to comment
Share on other sites

6 hours ago, mcoulton said:

Thanks very much for the help. 

Neverenoughwatches - I did your trick and looked down the winder from the plunger end - not the arbor winding end - and that naturally orientates the hook with the hook on the arbor that came out of the barrel.

ManSkirtBrew - Thanks for the Esslinger article. I'll make a note of it and add in my comments. 

 

This way just saves having to figure things in reverse. You see it or rather imagine it as is. Without both handed winders the spring can be released into a spring holder that new ones arrive in, and then just spun over to be popped into the barrel. 

Link to comment
Share on other sites

8 hours ago, mcoulton said:

If I understand it corectly, then I want to wind the mainspring using the blue dot (left-hand / counterclockwise) winding arbor?

which watch does this mainspring barrel come from

the majority of watches will use a right-handed handle and they will wind in a clockwise direction. Some watches though are left-handed like Seiko watches. Or typically 18 size American pocket watches are left-hand.

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Now I'm completely confused, it would appear that the epilame  is oleophobic  as @Marc states: This oleophobic  behavior can be seen as beading of the droplet (as above) which stops the oil spreading which is supported by what we observe on treated/untreated cap stones (for example), but as @VWatchie states this should make the drops more mobile, and not less mobile which is the opposite of what we want. In fact this beading and high mobility are desirable properties in things like smart phone covers, see below.  I am fairly sure that epilame doesn't make the droplets more mobile, so maybe its a strange coating with dual properties that are both oleophobic and cohesive/adhesive resulting in low mobility?? This may explain the high price??  
    • The description there is exactly how it's done, and it's very well written!
    • Would it be correct to say that the stronger the mainspring, the thicker the oil should be? So for a fusee mainspring, should a thick grease be used?
    • I started on pocket watches as they are easier to work on than wristwatches. Many had gold cases, which is why there are so many movements for sale. I was always on the look out for cases, for as Nickelsilver says,  a 16s movement will fit any 16s case* (with tweaks to the stem). I also started hand winding mainsprings, before I had winders. It can be done without damage, but it's quite hard on the fingers.  But you can make homemade winders, see here      * some movements, eg "railroad grade", have a setting lever on the edge of the  dial at about the 1 -2 o'clock, so need a special case.
    • Ok, on your movement plate you can see a star wheel on the right, this is the silencer, if you rotate the hands by hand through each hour you will see that eventually it acts upon the cam which moves the lever and in turn lifts the lifting lever thus stopping the chimes and strike working.  What you need to do is get your clock to 11pm and also turn the star until the cam lifts the lever and stops the action. The star wheel has a small spring that gives it a positive action between each movement, so once at 11pm you can rotate the star wheel around by hand until it stops the action at 11pm. Hope this makes sense to you.
×
×
  • Create New...