Jump to content

Hello from somewhere in the Cotswolds, UK...

DigitalM

By DigitalM
in Introduce Yourself Here

 Share

Recommended Posts

DigitalM New Member

DigitalM

Posted
Posted (edited)

Hi everyone

I started watching lots of youtube watchmaking vids during covid lockdown to get away from the horror and unbearable news that was unfolding. I'm in my 50's and had a fairly scary early encounter with covid, coming down with it a few months into lockdown as my daughter, who still lives at home and works in the care sector with elderly people, was exposed to it due to all the hospitals discharging patients back into care without thorough checks first. People like 'nekkid watchmaker' and 'wristwatch revival' really helped me to get through, with their love of the craft, natural enthusiasm and gentle humour, in a subject that was a million miles away from the 24/7 covid news misery.

I took one of Mark's courses which was excellent and very easy to follow. I grabbed an ETA 6498 (seagull variant) and tried to disassemble along with the guide. I had such problems with one of the shock springs, eventually losing it, along with the jewel, "somewhere", that it quite disheartened me. Things then got really busy with work for quite a while, and while I carried on watching and enjoying my youtube subs, I left the ambition of watch tinkering to one side.

I think I'm ready to have another go as a while back I bought another whole seagull movement because I couldn't figure out how to buy the new bits – I would have asked for help here but couldn't join this forum for some bizarre email related reason, but thankfully that's been resolved and here I am, saying hi!

I'm frankly scared half to death that I'll just ping another part into oblivion. I'm sure some people won't understand faltering over such a thing, I'm probably just not blessed with confidence on this sort of micro-scale operation, maybe it's because my vision isn't what it once was. I don't seem to have this sort of a nervous issue with almost anything else!

Reading all that back it all sounds a bit of a downer. It wasn't meant to be. Quite the opposite. I can't tell you how much I'm fascinated with the mechanisms and procedures, and I'm very grateful to those who put such great content up - it does way more good in the world than just teaching people about watch repair and servicing. 

Anyway, hello! And thanks for letting me get that off my chest 😆

Edited by DigitalM
grammar!
Link to comment
Share on other sites
grsnovi Distinguished Member

grsnovi

Posted
Posted
2 hours ago, DigitalM said:

People like 'nekkid watchmaker' and 'wristwatch revival' really helped me...

Welcome to WRT @DigitalM ! 

Those two guys probably are responsible for me being here.

I'm stalled partially through my first watch movement restore due to waiting on oils and tools (all of which should be on their way). Hopefully you'll decide to find a real watch that you'll take on as your first restoration. I decided to skip Mark's walk through and dive in. I have a 2nd grade 313 Elgin in the wings in case things go horrible with my first and I have a Buren 10.5 Grand Prix on the way.

I keep hoping that I'll find something amazing on eBay for cheap that will allow me to wear something that I brought back from the dead that I can be proud of.

  • Like 1
Link to comment
Share on other sites
  • 1 month later...
Michael1962 Distinguished Member

Michael1962

Posted
Posted

Welcome to the forum @DigitalM

Don't worry about your post and how you think it reads. I have done it as well and I was only looking at doing clocks. Not the microscopic world of watches yet.

It is very easy to forget that you are watching a watch be repaired and it is filling a 14" laptop screen when in reality that enormous picture is actually only about 32mm across.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • eccentric59
      404 Club Reboot

      By eccentric59 · Posted

      I went with 8.90£ because 12th century Italian mathematicians are always excellent topics to bring up when trying to get your guests to go home. 
    • Zendoc
      Without Our Forum

      By Zendoc · Posted

      As a beginner, I’ve found this forum invaluable. I doubt I would’ve persevered without its support. I’ve had the confidence to attempt things that seemed to me impossible only because I knew there were patient and giving folks gathered around this watering hole, available to share their skill.    I would very much like to know where to go if this one dries up and everyone needs to decamp.  There’s something special about the folks gathered in this group.  How to keep in touch?  
    • eccentric59
      Boley lathe motor silly question.

      By eccentric59 · Posted

      After a 3-week work fiasco that took up 137% of my time, I was finally able to get back to restoring a G. Boley 8mm lathe I picked up on eBay. I still need to do a bit of polishing on the tailstock but it works very nicely. Before and after pictures below. In any case, when I was reassembling the motor I wasn't quite sure which side the pully attached to, or if it matters. My question is ... does it matter? The listing photo below shows it the reverse of how I have it now, but it seemed that the cord and the reversing lever(s) should be on the right away from the belt.   
    • Zendoc
      Deciphering mainspring specifications…

      By Zendoc · Posted

      Thanks Richard.  That’s clear.   So - another question - how much latitude is there in barrel and spring sizing? Say I have have measured the ID of my barrel to be 9mm and (all other mainspring specs being equal), the closest match I can find for a replacement mainspring is listed with an 8.5mm barrel size, is it acceptable to fit the smaller spring in to the slightly larger barrel without compromising anything functionally?  I’m in this situation now with an AS 1686 which has a 9mm barrel, but the closest replacement I can find has an 8.5mm diameter listed in its specs.  I can find an alternative 9mm spring, but would have to accept a different thickness.  I’m unsure how much wriggle room is acceptable, or whether in mainspring sizing, there’s a priority - ie thickness over barrel size etc. Thanks again for any info.  Cheers, John  
    • tomh207
      Without Our Forum

      By tomh207 · Posted

      We already have a Facebook group run by Mark , so this is a bit moot. Search for “Watch repair lessons” group.   Tom
×
×
  • Create New...