Jump to content

Double quotes?

Nucejoe

By Nucejoe
in Help & Support With This Website

 Share

Recommended Posts

Nucejoe Distinguished Member

Nucejoe

Posted
Posted
22 hours ago, jdm said:

If you enter these words inside double quotes on the search box top right you will have all the relevant discussions to learn at least the basics. 

Would you show a double quotes, is it  like this ""    or this  ((          😩

 

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
49 minutes ago, watchweasol said:

I think what jdm is trying to put over in double quotes is        "hairspring"    The quotes as such ive it a try

Not for "hairspring", for single word searches no quoting is necessary. The original question was about "timing screws" and "timing washers", to search for that literally you need to use double quotes, otherwise an OR search of all words entered is performed.

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
1 hour ago, watchweasol said:

Hi  just trying to give an example of the use on the double quoted

Pardon my pedantry. Unfortunately the search function of the forum is not the best around, it doesn't even do all what it promises, so I was trying to explain one thing that at least does right.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Geotex
      Generic screws for unknown movements

      By Geotex · Posted

      Chief- The picture below shows the three parts from the dial side that are most useful to "fingerprint" a movement in conjunction with the diameter of the movement.  That's why forum participants are always asking for dial side photos in posts asking for identification.  As far as the setting lever screw, it actually sits loose in the main plate. The threads engage the setting lever below, and the elongated stem above the shoulder sticks through a hole in one of the bridge plates so that it's held captive if unscrewed all the way.  So you may be fine as far as that goes. 
    • Chief
      Generic screws for unknown movements

      By Chief · Posted

      So I found what I believe is the setting lever screw! Am I right in thinking the screw next to the click is the correct one for the setting lever? However if it is, it doesn't fit in the hole which I believe is for it! I can get the lever to sit nicely on the stem and line up with a hole, but the screw only goes as far as the shoulder and stops. It's as though the hole is too small! The dial side has been disassembled by the way, the other wheels are in my tray
    • AlanB
      Gilding after silver soldering

      By AlanB · Posted

      When faced with say a pocket watch bridge which is cracked, silver soldering to repair is often the only option (hopefully someone wasn't there before hand with soft solder). I can generally do this succesfully and tidily with a small torch and miniscule pieces of silver solder, but on parts which were mercury amalgam gilded the heat can have have a deleterious effect on the finish.   I keep wondering if there's a good way to refinish these - and despite having the needful items would rather avoid using the mercury process.   In the past for electronic work I've gold plated PCBs but this involved gold potassium cyanide solution, which also doesn't realy belong at home. I've read that there are now safer alternatives but couldn't find more detail (and importantly how similar are the results to amalgam gilding, since I wouldn't want to refinish the whole watch). Pointers would be very welcome (and yes, I know solutions containing gold won't be cheap!) Alan
    • Neverenoughwatches
      Can anyone identify what this is? Part Two

      By Neverenoughwatches · Posted

      The first one is an Unruh max stake for pushing out staffs
    • JonC
      Can anyone identify what this is? Part Two

      By JonC · Posted

      Ok so with the great answers for my previous question may I ask what these two attachments are used for. The one with the red knob is I assume used for hand setting the seconds hand? Jon      
×
×
  • Create New...