Jump to content

Another toy has been added to my workshop


Recommended Posts

Another toy has been added to my workshop.A AmScope (SE400-Z) 10X-20X LED Binocular Stereo Microscope Boom Arm + LED Gooseneck. It was supplied with two pairs of eyepieces wide field WF10X and WF20X.The reason for this latest purchase is I have a issue with my back and it is suspected it is a condition named spondylitis. There is no medical cure just various pills and exercises to help but stooping over a workbench for long periods becomes very painful and without doubt aggravates it.  So the idea (which was recommended on the YouTube site Choroglide) being less stooping by using a microscope and this particular scope has a large working distance of 9” although in reality 8”.  But nevertheless I can now work and inspect watch movements with a better posture. Early days yet but it seems to be making a big difference. I have now ordered a pair of WF5X eyepieces which will give an even wider view.

I am now the owner of three microscopes. I have a Bausch & Lomb stereo microscope which has really good magnification if required over my lathe for fine work such as balance staff work. My workbench has now two microscopes an Olympus stereo microscope with a magnified light source via a fibre optic cable to a ring light. This scope has superb clear lenses and can also give incredible magnifications. But a very short working height hence the latest purchase.

The AmScope has good lenses but certainly does not have the same quality and clarity lenses as the Olympus. The light source is also via a gooseneck led light and again this is not as good as a ring light. However this scope cost just £166 inc. postage so IMO it is still really good value and well worth the investment and I suspect this will be the go to scope for most of my work.

21D7FD31-A27E-4DA1-935C-65B95BD8B42C.thumb.jpeg.b7d9e51e10307eb5e1d2d4bcfd42eb21.jpegI

Bausch & Lomb over my lathe.

4F166AE9-0155-4B75-A328-D8EE5C47D0C3.thumb.jpeg.ae0faa92045692d64cadcee700b9b89b.jpegA77110C9-84AB-4CF4-8E44-9A5CFC6649B9.thumb.jpeg.720d559825842dfbd892f7b367693f71.jpeg

Olympus + light source 

 

750FFE03-29BC-4ED2-A702-304227631322.thumb.jpeg.0f4df6eda998e430816563ed47dea6aa.jpeg

The new toy.

  • Like 2
Link to comment
Share on other sites

Clockboy I’m sorry to hear you might have spondylitis. That is what I have in my neck and it caused me to give up watch/clock making many years ago. I have to take citalopram 20mg each day which is an antidepressant as my neck locks and it scares the s**t out of me. Posture is so important in the field of working on watches and clocks. Try not to sit for long periods and take frequent breaks.

Link to comment
Share on other sites

You may find some Yoga helps with the posture and the spondylitis.

My posture has been pretty poor over the years.  Too much sitting slouched over a computer, and of course I'm not as young as I once was, so my sister in law, who is a yoga instructor has been working on improving it, with some encouraging success. A good physiotherapist would also help, (with similar exercises).

As to microscopes, I have a couple, and coupled with good light, they do make a huge difference to what is possible. Great for sorting out hair springs, and identifying dirt on what to the unaided eye appears to be a perfectly clean jewel.

Link to comment
Share on other sites

5 hours ago, oldhippy said:

Clockboy I’m sorry to hear you might have spondylitis. That is what I have in my neck and it caused me to give up watch/clock making many years ago. I have to take citalopram 20mg each day which is an antidepressant as my neck locks and it scares the s**t out of me. Posture is so important in the field of working on watches and clocks. Try not to sit for long periods and take frequent breaks.

Thanks OH I am thankful I don’t need horology for a living. The medics have tried me on various antidepressants but unfortunately I had a adverse reaction with all of them. Pain killers exercise and as you say not spending too much time sitting for long periods. 

Link to comment
Share on other sites

I feel for you, I have the other version, Spondylosis, were all my discs are vanishing, I find working at the microscope helps as mine is set a little too tall for normal use but in my case because I have to sit very upright to see it helps my back, so I can do a few hours at the bench without pain.

Paul

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Saturday morning 27/4 Sunday evening 28/4 Monday evening 29/4 Floor has a drain in the middle so I am hoping that there is very little fall on it, if any. Room is about 2.5 x 2.5 metres square. Can only use about 1/2 of one wall on the right of the pictures which has a sliding glass door in it. And only about 3/4 of the wall to the left of the pictures as it has the door to the house in it. Progress. 🙂 
    • This makes much more sense now, the oil is withdrawing itself to make as little contact with the epilame as possible. Same principle as wax on a car creates a hyrophobic surface that makes the cohesive properties of water molecules pull together.  The water beads run off only when under the influence of gravity but still remain cohesively beaded up. And as mentioned earlier a pivot would keep the oil in place on a cap jewel.  Epilame on an escapement would be a different scenario, there is nothing to hold the oil in position if gravity tugs at the bead to move, plus the escape teeth pull the oil about Maybe this is why its suggested to run the watch for a short while to remove the epilame to make two oleophobic surfaces either side of the oil, creating a ring of fire 🔥 around it 😅 The oil is repelled by every surface of the epilame even that which it sits upon. So the oil pulls together to make as little contact with it as possible, but the oil cant float above that area, it can only sit there on top of it. Under gravity the oil could potentially run away as an oil bead, unless the epilame has an adhesive property which i dont think it does ? So something else keeps it in position ie a pivot under a cap jewel . But that isn't the case in a pallet jewel situation. 
    • As with every skill it watchmaking, it takes practice. Notice at the top of the document it says, "Practical work - 40 hours".  I can get the balance wheels 'close enough' to flat, but never seem to get them perfect. Same with gear wheels. Guess I need more practice.
    • Has it got a beat adjustment on the platform or is it a fixed hairspring? in short what you are looking at to get it just about in beat is to get the roller jewel sitting dead centre between the banking pins. So remove the platform and take of the pallet fork and escape wheel to give you clear line of site, sit the platform with the balance in place and with it level look between the banking pins and see if the roller jewel is sitting between them, if it is nice and central its there or there abouts in beat, if its not the the position of the pinned end of the hairspring needs to be adjusted to move the roller jewel into the correct position, thats why I asked if it has an adjustment on the platform or not, if it has its an easier job. 
    • I've managed to adjust it. I'm going to try and explain it as well as I can with my limited horology knowledge but I hope it helps someone in the future. There is a cam to the right of the front plate as shown in the picture. As the clock ticks along, the pin indicated in the gear comes around and slots into one of the silencer cam gaps, turning the cam. The pin completes a full rotation in 2 hours. To adjust the cam to start at the right time set the clock to just before 7. I did 6:45. Then I turned the silencer cam anticlockwise, which spins freely, until it pushed the silencer lever up and was placed just before the drop. Just before the 7AM indicated in the picture. All I then had to do was progress the hands to 7-7:15which made the pin slot into the silencer cam gap and turn the cam so the lever comes down again, unsilencing the clock. That was it. If anyone comes across this issue again I'd be happy to assist. Thanks again to everyone that helped. Hey Transporter! Thanks a lot for the reply. That was a really good explanation and I'm sure it would have made my troubleshooting a lot less painful haha. I'm sure someone will find it useful in the future. Thank you again for taking the time to try and help me out with this.
×
×
  • Create New...