Jump to content

Spring-loaded crown gaskets

JohnC

By JohnC
in Watch Repairs Help & Advice

 Share

Recommended Posts

JohnC WRT Addict

JohnC

Posted
Posted

Hi all,

I am working on a couple American watches from the 40s-50s, some of which have crown gaskets that are badly degraded, and mounted on springs between the crown and the case. Can someone advise me on replacing these? I see there are gaskets on Cousins, but these seem to be a) caliber-specific and b) not spring-loaded. Any info and suggestions would be very helpful. Thanks!

Link to comment
Share on other sites
Tudor Distinguished Member

Tudor

Posted
Posted

Can you get some measurements on that o-ring? I think you will be OK to use a (esy to get) Rolex crown o-ring. They have a few sizes of crowns and therefore corresponding o-rings. If you measure, and give your preferred supplier a call, they may be able to help.

"off the shelf" standard o-rings (even the odd ones) don't go small enough. I have some of the small "standard" o-rings just in case, but I've not found use for them in a watch yet.

  • Like 1
Link to comment
Share on other sites
JohnC WRT Addict

JohnC

Posted
  • Author
Posted

Thanks, maybe I can get a measurement. One thing I am wondering is, should I just be using generic o-rings on all watches I overhaul? I've only come across a few that have crown gaskets, but it seems like a smart idea to just use them whenever possible. Seems like you're saying that it's hard to find standard o-rings of a suitable size.

Link to comment
Share on other sites
Tudor Distinguished Member

Tudor

Posted
Posted

Yeah, really tiny o-rings are non-standard. If you search the Parker O-ring catalogue, you'll find all the "dash numbers" that correspond to ID and cross section. But the smallest standards are:

5-051 which is .070 ID X .040 cross section (thickness of the ring itself) so this is .150 OD (INCHES)

2-001 .029 X .040 (.040 cross section is 1.02mm, so rather "fat"- most are 0.5mm cross section)

2-002 .042 X .050

2-003 .056 X .060

Then the "real" standards start

2-004 .070 X .210 (1.78mm cross section)

and up from there...

If those first sizes will work, you can get bags of 10 or more for less than what one "watch" seal will cost. There are also a few other non standards that are smaller but those are harder to find. Check McMaster-Carr...

  • Thanks 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • watchfellow
      Venus 178 hour counter creep

      By watchfellow · Posted

      Hi everyone, I put together a Venus 178 recently, but found that the hour counter "creeps" ie. runs when the chrono is disengaged. This is the similar type of setup as the Omega 861, where the hour counter is driven off the mainspring barrel, but stopped when the chrono is disengaged by a friction spring.  Am I correct in assuming that the friction spring for the hour counter driving pinion should be dry? I am guessing that the issue will be either the spring or the driving pinion, but while the driving pinion has some wear the spring looks decent.  I've attached a couple of photos in case anyone has any tips. Thanks in advance!
    • watchfellow
      Setting power reserve on LeCoultre Futurematic

      By watchfellow · Posted

      Thanks everyone for the replies. It seems setting the hand is a bit of a guessing game, and I thought there would be a very specific way to do it. Since the reserve indicator hand moves clockwise as the spring is wound, I tried setting it right at the start of the black side. But setting it there doesn't really make sense, because by the time the spring is halfway wound, the hand is only at the end of the red side... In my head halfway wound shouldn't mean the hand is still "in the red."
    • Chief
      Intro

      By Chief · Posted

      Lovely part of the country! I spend most of my days driving along the A64 for work in and around York. I'll be sure to drop plenty of questions soon! I've actually got a couple of watches on the way that I'm pretty sure I'll need some help with! They look pretty beat up from the pics but I love a challenge and an excuse to buy more tools 🤣
    • oldhippy
      Help - London Elliott Mantle Clock Night Silence

      By oldhippy · Posted

      I have two of these in my home. You need to remove the movement from the case, take off the hands and remove the dial and take a few good photos of the front plate so I can see what the problem is. The round nut unscrews and the hands pull off pull them off from the center and not the tips as you could break them. 
    • Neverenoughwatches
      What is this tool !

      By Neverenoughwatches · Posted

      I asked the question of one of the sellers. Its for removing the pins and making the holes in motorbike drive belts. God knows why they were both in two seperate joblots of watchmaking tool, thats bizarre. I haven't posted your setting lever steel yet mike, been busy with my mum past few days and had a locked myself in at home lazy watch repair day today 🙂 but I'm out tomorrow so i will get it off to you then. 
×
×
  • Create New...