Jump to content

Cleaning Chemicals storage and precautions


Fraczish

Recommended Posts

I promise this is not another thread about what to use! I have read the pinned thread on this twice and I'm satisfied with my lighter fluid (until it runs out) and IPA combination.

Just a quick question about storage and precautions as this is the first time I used IPA. The label of the IPA 99% gives all sorts of warnings. I fully understand it's a volatile substance.. is it any more volatile than the lighter fluid ive been using up to now? 

I currently use in a cool, dark, ventilated part of my garage, I wear gloves and keep the water in the US cold. 

The fluids are stored either in the original container or in the little jam jars with lids. Then in a box in the garage. 

Anything I should be more careful of/havent considered?

Link to comment
Share on other sites

I keep my 99% IPA in the cabinet in the bathroom. Though TBH, it's only ~80% now (marked as such with sharpie for future reference), because I cut it with some 70% to be able to eliminate a bottle and make some space. The grocery store near me keeps it on the shelf next to the 70% (or did in the before times). Don't leave it open on the edge of the table with one of those bitchy internet cats and you're probably fine.

For truly nasty stuff, I have a steel cabinet in my shop (not the same as where I work on watches). At present, I just leave the doors cracked, and make sure the shop doesn't get too hot or cold. Eventually, I'll get around to putting a vent in the cabinet, and maybe some sort of heating/insulation system. But that's for nasty stuff and whatever fits toward the nasty end of the spectrum.

Edited by spectre6000
Link to comment
Share on other sites

Hi  Its always advisable if possible to read the data sheet on the chemical and adhere to the manufacturers instructions,   If spec sheets are not available use commonsense.  spirits ie .    naptha ,benzine ,Ipa    etc keep cool and away from direct sunlight and far away from naked flame.     and as Old Hippy said don.t smoke.

 

  

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Welcome to the forum, enjoy. I have a varimatic that went  out of sequence because it’s hydronic oil ran very low. Must admit it’s still in my garage just know time to fix it. Purchased a cheap Indian Junta/ sonic Pearl as a stop gap a few years ago and it still performs perfectly so no incentive to fix the Varimatic. 
    • The plate is OK, thanks. It seems the answer to my question is that this is a 'hack' & for me another reminder that in general, one won't be the first person to be tinkering with an old timepiece!. As you day, I've been fortunate to have gotten some good advice and, just as important, encouragement. I've been lucky then not to have the balance spring break as a result of my novice 'ministrations' - but I did remember to 'stroke' rather than bend per se. The clock is of sentimental value to the owner so I'm relieved to have now got it running to time with the support & encourage of forum members like yourself.
    • Recently purchased a L&R Varimatic knowing that the piston does not fully rise in the cylinder. The likely cause is air in the system. The manual calls for using a bleeder cup, which is as rare as hen's teeth.Does anyone have any experience with this issue and if so, how did they resolve it?
    • Thanks ww, its maybe not as much of a bodge trick that i thought it was. 
    • Thank you for your introduction and welcome to this friendly forum. We all look forward to your contributions and continued involvement.  It would be nice if you told us a little about yourself.
×
×
  • Create New...