Jump to content

Sauce Pans and Today's Watches

Cliff
 Share

Recommended Posts

Cliff Member

Cliff

Posted
Posted

Initially, I fancied some of the large sauce pan watches that became trendy with Hip Hop. But having worn more than a few over the years, I now seldom wear anything over 40mm, preferring instead 34 to 36mm case sizes, because they are functional and tuck in nicely in under the sleeve . Most of all, you can work with a smaller watch, as opposed to the newer sauce pan size varieties, which inadvertently act as bump magnets and are uncomfortable when worn all day, especially if you are active.

What are your thoughts on the move away from smaller case sizes to BIG watches?

 

watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi  Having worked on a few of the big jobs it seems the ones I got were just big dials with a Miyota 2030/35 movement driving the hands. Ostensibly fashion watches although some were mechanical again with a big dial, like you I prefer the smaller ones that fit snug              

  • Like 1
dadistic Distinguished Member

dadistic

Posted
Posted

40mm maximum for me, with my skinny wrists that's pretty big.

38mm is perfect for me in a modern watch.

In vintage, my favorite is the Bulova "23" from the fifties. These guys were pretty small, 33-34 mm usually, but at the time smallness was an indicator of "high tech" and elegance.

It's nice wearing a watch that doesn't clang around on the wrist. Maybe I should move to pocket watches :-)

  • Thanks 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • watchweasol
      Clock newbie

      By watchweasol · Posted

      A helpful way in aid of assembly is to place all the wheels in their respective places, place to plate on the top and fit a couple of the nuts onto the pillars. This stops all the wheels wobbling about as they are lightly held by the plate, you can manoeuvre the pivots into their holes, using a tool , usually home made or can be bought on eBay. I made my own. As the pivots align and fall into place screw the nuts down a bit to keep up the tension on the plate untill all wheels are in place then tighten down sufficiently to keep the plate in place whilst checking the end shake on ALL wheels and their location when all is good only then tighten down the plate.
    • Titanium
      Your nicest antique tools or materials?

      By Titanium · Posted

      I'd say my Pultra 10 lathe. It is just so well made and everything fits so tightly together.
    • clockboy
      Caravelle 11DO 17J vs 7j

      By clockboy · Posted

      Welcome to the forum, enjoy. 
    • nevenbekriev
      Full plate watch, Suitable tool for adjusting & testing pallet stones?

      By nevenbekriev · Posted

      Yes, the specific old tools do exist, but may be having one is not needed as they are not cheap, and also You will be able to do without it well enough. My advice will be to use regular depthing tool and adjust it for the exact distance between pallet fork and escape wheel bearings from the watch. Then remove the shellac from the pallet that now doesn't pass the ew teeth and move this pallet in. Then put the pallet fork and ew on the depthing tool and check how they lock. They should not lock when the pallet is in, but You will little by little move the pallet out and locking will appear. Then move just an idea out for reliable work and apply shellac, then check if things are still the same. You have to observe where the teeth fall on the pallets - it must be just a little below the edge between impulse and rest planes. Then You must check how everything behaves in the movement This Potence tool is so ingenious, but actually, the traditional way to do the things is much more simple. Arrange the parts not on the pillar plate, but on the cover plate. Only the central wheel will remain on the pillar plate, secured by the cannon pinion.
    • Mercurial
      Full plate watch, Suitable tool for adjusting & testing pallet stones?

      By Mercurial · Posted

      There is a tool that was made for setting up and adjusting escapements of full plate watches.  There were two styles, the picture below shows both of them.  The lower tool held a movement plate and the vertical pointed rods were adjusted to hold the unsupported pivots of the lever and escape wheel.  There was also a version of this tool that had 3 adjustable safety centres so that the balance pivot could be supported by the tool :  The other version I’m aware of is the Boynton’s Escapement Matching and Examining Tool came as a set of two or three clamps that gripped the watch plate and held the safety centres for the pivots : These do turn up on eBay from time to time.  For some escapement work, you can set up the parts in a regular depthing tool, with the centres set according to the distance between the corresponding pivot holes on the movement.  I hope this helps, Mark
×
×
  • Create New...