Jump to content

German WECKER D.R.P. & G.M. Alarm Clock


transporter

Recommended Posts

Well just picked one of these up at a local antiques fair, cost a fiver missing crystal and the alarm hand has snapped but minor faults. 

The picture is taken from the internet as mine is in the workshop at the moment.

the whole thing is only about 2” square, I popped out the movement  earlier just for a look and the balance is ok but it’s filthy so will benefit from a good clean etc.

has anyone any info on the movement please, not worked in one before and don’t want to wreck it when I get round to bringing it back to life, cheers in advance

 

0C54389D-7292-405A-AEE0-D40FDFE6152B.png

Link to comment
Share on other sites

Adding a few more pictures of mine, just dropped the movement from the case and now back together awaiting the love.

Haven’t found a makers mark or cal. But don’t really expect to, so I hand it over to the forum for any additional information that I might need when I start on this gem.

E1D4C82C-7153-4638-B516-E64E13E1287C.jpeg

0D6B882A-AAB7-44CC-AF57-79D69475C362.jpeg

E8AAB41C-BB9F-460D-A907-70473C6940EB.jpeg

7809A324-C7BD-4F17-AB73-CB3AC4ED8170.jpeg

0773A4A4-8260-4AC9-8A36-4FCAF3EE9EFF.jpeg

53BA85AC-879F-4F79-8DCD-72CDE2A3192A.jpeg

Link to comment
Share on other sites

Whilst I was taking the pictures I gave the balance a little nudge to make sure the staff was ok and it decided to give a couple of very painfully slow tick tocks so all is well, will just need to inspect and clean etc and get a new crystal and Alarm hand and hopefully another to the collection. But first I have to finish me “like” an 8 day pocket watch!!!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Yes, I was referring to the (jewelled) gear train with HP (most of the time, I use 1300, but when Rolex says 1000, I'll use 1000).
    • did I miss the update of the message of something changing?      
    • I suppose it would depend upon what your lubricating with those? for instance what does the manufacturer say about those lubricants? I have a PDF from the manufacture and a rather peculiar statement found on the bottom of the chart. my suspicion is the reason the recommending would be without epilam the HP oils like the spread except when they're in Ruby jewel's with steel pivots. tableEN lubrication 2020.pdf
    • These types of hairsprings become weak with age and very fragile. Which I expect it is that giving you trouble, and that wheel is not the correct one, if it were not bent I don't think the movement would run as the teeth are not the correct height. The problem you have is price which depends on you. It can be repaired but is it worth it to you, because there is little value in the clock. A wheel can be made and hairspring replaced. Or hang on to it and keep looking on ebay which is your best bet for replacement parts or even a complete movement but it will be like finding a needle in a haystack. 
    • I did that also for a few movements - well, mainly in/around the train jewels. I made big efforts to epilame the mainplate WITHOUT getting Epilame into the Pallet fork jewels (where it's not supposed to be, right?). I made litte barriers with Rodico around that jewel and used drops from a syringe to apply on the rest.  However, I've now stopped doing this. For three reasons: 1. It's a hassle and consumes more of this liquid gold. 2. I didn't see the need when using HP1000/HP1300 lubricants and grease for most part. The two places where I'd use 9010 (i.e. escape wheel and balance) receive Epilame in specific places... or the cap-jewel-setting of the balance suspends the oil sufficiently be capillary action (see my "conflict" about using Epilame on the balance jewels).  3. Lastly, and here I really wonder about yours and others' experiences: I felt that applying Epliame to the train jewels left them looking hazy (borderline dirty) compared to the (painstakingly achieved) sparkly clean results of my cleaning process. I just can't help but think that the Epilame residuals would mix with the oil and cause more friction/wear. I don't know.    simple: it'll stay there. It won't move any further. That's exactly what is happening if you epilame a cap stone. You end up placing the 9010 right on top of the epilame and the oil will sit nicely on that spot.
×
×
  • Create New...