Jump to content

New Fella Here

AlexC

By AlexC
in Introduce Yourself Here

 Share

Recommended Posts

AlexC New Member

AlexC

Posted
Posted

Hi There,

 

Thought i had better pop in and introduce myself.

Just joined up to ask a question on a Gucci thats been given to me thats broken. Also have a Tag Heuer Aqua Racer which is my every day watch, and is looking a bit worse for wear at the moment ! Future questions will be on how to polish it up a bit !!

 

Looks like an interesting hobby getting old watches working again, possibly a step too far with my big suasage fingers though, we'll see !!

 

Cheers

Link to comment
Share on other sites
Vich Distinguished Member

Vich

Posted
Posted

Hello Alex,

Don't worry about being cack handed as I have survived quite successfully and it only makes the successes more enjoyable. As for failures you just try to look philosophical and state it was a good learning experience.

Welcome to the forum and if you do feel like giving it a try (and why not !) the folks in here will always try to help out with the problems. Small bit of advice, photo before and after you remove anything - gives you a head start getting the bugger back in the right place [emoji6]

Cheers, Vic

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Bonefixer
      AS2063 - hand setting

      By Bonefixer · Posted

      The part was how it fell out of the movement - the train wheel bridge wasn’t screwed in.    I’ll probably dismantle the part, if I can, to work it out.    The train of wheels ran fine - it was only once the keyless works were installed I noticed the problem. 
    • mthomas828
      Balance staff sourcing?

      By mthomas828 · Posted

      Hello, I am about 5 months into watchmaking and I love it!   The attention to precise detail is what really attracts me to it. (and the tools!) I am working on a 16 jewel 43mm pocket watch movement.   There are no markings besides a serial number (122248) .  The balance staff needs replacement. The roller side pivot broke off.  I successfully removed the hairspring using Bergeon 5430's.  I successfully removed the roller using Bergeon 2810.   Did i mention I love the tools?! I removed the staff from the balance wheel using a vintage K&D staff removal tool  with my Bergeon 15285 (that's the one that comes with a micrometer adjustment so it can be used as a jewel press as well as a traditional staking tool...it's sooooo cool...sorry..  can you tell i love the tools?) No more digressing..  I measured the damaged staff in all the relevant areas but I have to estimate on some because one of the pivots is missing. A = Full length  A= 4.80mm  (that's without the one pivot...if you assume that the missing pivot is the same length as the other pivot (I'm sure it's not)  then A = 5.12 mm...(can I assume 5.00mm here?) F=  Hair spring collet seat  F=  .89mm   (safe to assume .90 here? .. I am sure that my measurement's would at least contain  .01 mm error ?) G = balance wheel seat  G = 1.23 mm  (1.20mm?) H  =  roller staff  H =  .59mm  (.60 mm?) B  = bottom of the wheel to roller pivot   B  = 2.97mm  (3.00 mm?)     here I am estimating  again because this pivot is missing. So my friends, and I thank you profusely,  can you point me in the right direction as to how to proceed? Do i buy individual staffs?  or an assortment?   Since I don't know exactly the name of the manufacturer, will that be a fatal hindrance?   Tbh, I'm not even sure what country of origin this movement is. Thank you!    
    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      Thats why i asked that question earlier, what happens if lubrication is placed directly on top of epilame ?  As opposed to walled within its non epilamed area . I'm not saying its right, i have no idea , just asking questions. 
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      thinking of where epilam should be removed did you know there was a patent that covers this? At least for the escapement I'm attaching it. GB1057607A-1 epilame.pdf
    • LittleWatchShop
      Movement holder made with 3D printer

      By LittleWatchShop · Posted

      Back home...printing now.  Will report results
×
×
  • Create New...