Your Current Projects and Achievements
If you would like to discuss your current projects or show off your latest watch repair achievement and it is not an actual walkthrough please post here.
SECTION RULES
This section if for posting the results of your labours with a particular project. If you wish to post a full walkthrough then please use this section.
535 topics in this forum
-
- 1 reply
- 122 views
-
- 0 replies
- 81 views
-
- 4 replies
- 635 views
-
- 15 replies
- 596 views
-
- 8 replies
- 2.1k views
-
- 6 replies
- 1.7k views
-
- 0 replies
- 768 views
-
- 13 replies
- 2.4k views
-
- 0 replies
- 1.1k views
-
- 4 replies
- 996 views
-
- 1 reply
- 406 views
-
- 12 replies
- 459 views
-
- 5 replies
- 1.6k views
-
- 2 replies
- 866 views
-
- 10 replies
- 1.8k views
-
- 5 replies
- 1.3k views
-
- 10 replies
- 871 views
-
- 2 replies
- 309 views
-
- 30 replies
- 2.4k views
-
- 11 replies
- 945 views
-
- 3 replies
- 940 views
-
- 4 replies
- 1.3k views
-
- 3 replies
- 365 views
-
- 1 reply
- 493 views
-
- 0 replies
- 269 views
-
Topics
-
-
Posts
-
By nickelsilver · Posted
These are all American movements (with the exception of the "Rubis"), and are all almost certainly "negative set" which means the stem is part of the case. So it's normal that they are all missing- they are with their cases. You will need male square bench keys to wind/disarm them. Vintagewatchstraps has a great writeup on the different systems. But basically, any American "x" size movement will fit any case for that size, possibly with some adjusting of the stem position. With Swiss movements, there is some interchangeability between calibers, usually within the same maker's range, but not really overall- there are thousands of different stems out there. -
Hi, I'm very new to watchmaking and this is my first time posting here. I've bought a lot of 10 vintage pocket watches size 0s from e-bay and just got them today. Most of the balance wheels sprung quite freely and thus seemed like a worthy endeavor as a first batch for exploration. I've just realized that none of them have any winding stems. Is there any way I could source appropriate winding stems for the movements? There seems to be assortments of various stems selling in bulk on aliexpress, but would any of them fit? I've read on other threads that some people lathe their own stems (which is waaaay out of my current skill set, which is pretty much nil). Others say that you 'just have to try a few and see if they fit'. I would much appreciate any advice for this matter. Thanks! -
By LittleWatchShop · Posted
Nice work. In the last year, I have been servicing Accutron 218s. I have the official Accutron hoder that provides electrical contact to the movement. It is a pretty clever design. There is a cut in the ring of the holder (shaped like a "C"). When in relaxed state, the holder is slightly smaller than the watch movement. You spread the cut slightly and drop the movement in and release. Very clean. I have made 3D versions of this setup. Have not explored using it generally for other movements. -
By rossjackson01 · Posted
Double Oooooo Removal tool? Dreamed of one of these. However, Kalle on Chronoglide showed everyone my system with the pegwood. Worked a treat. Felt so chuffed to be mentioned. https://www.youtube.com/watch?v=tTFrXjiyGKc 46:40 for the wheel removal. Mentions me at 50:00 and does the removal with the pegwood. Felt like my 15 minutes of fame. -
By rossjackson01 · Posted
Sirius. Thank you for helping others with that information. This is why this forum is so good.
-
