Jump to content

Tudor/ETA 2750 Stem

MattWatch

By MattWatch
in Watch Repairs Help & Advice

 Share

Recommended Posts

MattWatch Watch Enthusiast

MattWatch

Posted
Posted

So i just picked up a stunning old Tudor, minus the crown! I believe this has the ETA 2750 movement.

The stem seems quite short to me. Fitting another crown there is not enough "travel" to fully insert them stem when it's re cased. So I'm thinking the old crown may have snapped off?

Anyway, main problem - buggered if I can get the stem out! I assume it's the little button near the stem but pushing on it won't release it and I'm terrified of pushing too hard and pushing the button out the dial side.

Any ideas please?!? Am I heading in the right direction with that being the correct stem removal procedure?

Ta, Matt

Screenshot_20180928-214540.jpg

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted (edited)

You won't push the button out dialside as there are parts over it. But you could disengage parts in the keyless work so it's gets hard to put the stem back into place again. It's the right button so need to press on it to get the stem out. If it doesn't work take the hands and dial of. 

Edited by rogart63
Link to comment
Share on other sites
MattWatch Watch Enthusiast

MattWatch

Posted
  • Author
Posted
11 minutes ago, rogart63 said:

You won't push the button out dialside as there are parts over it. But you could disengage parts in the keyless work so it's gets hard to put the stem back into place again. It's the right button so need to press on it to get the stem out. If it doesn't work take the hands and dial of. 

Thanks for this. Ok, odd, using a flat blade screwdriver I can actually feel the button depressing but the stem will....not release. I wonder if there's a problem somewhere within?

Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

Choose the LARGEST HEAD screwdriver to go through the hole B-B, push down on the button as you like, the screwdriver stops at a point, by a step, provided as the diameter of the hole A-A  the button is in, is smaller. The step is as deep down the botton is to go to release the stem.

The key to proper, risk free operation is the SIZE of the scrwdrivers head, to be larger than the diameter of the small holeA-A,  just so it can,t get inside the smaller diameter hole.

Regards

1538193917509-1451373784.jpg

Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

Modified to show the screwdriver head/tip.

You can work with a smaller screwdriver or any tool, as long as, it dosn,t enter the smaller hole.

In case the stem dosn,t want to come out, rotate them stem, a slight pull wont hurt. 

Keep us posted please.

Regards

15381943919401939652397.jpg

  • Haha 1
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

I fell in love with this tudor.

Getting  charged a fortune on one hand and risk getting this beauty damaged. So I suggest do not use a flat blade screwdriver, but a round bar, hard strong polymer stick, it would be worth the trouble of cutting one out for the job. Polymers wont scratch the surface.

Once the button is pushed as far down as the designers calculated, you may need to push/pull the stem in and out, turning the crown can help.

Though stem extender is normally used, you wouldn,t want anything less than perfect for such a jewel.

Rdgards

 

Link to comment
Share on other sites
MattWatch Watch Enthusiast

MattWatch

Posted
  • Author
Posted
6 hours ago, Nucejoe said:

I fell in love with this tudor.

Getting  charged a fortune on one hand and risk getting this beauty damaged. So I suggest do not use a flat blade screwdriver, but a round bar, hard strong polymer stick, it would be worth the trouble of cutting one out for the job. Polymers wont scratch the surface.

Once the button is pushed as far down as the designers calculated, you may need to push/pull the stem in and out, turning the crown can help.

Though stem extender is normally used, you wouldn,t want anything less than perfect for such a jewel.

Rdgards

 

Thanks also for this, much appreciated.

As you seem to be a fellow fan, here's a couple of pics of it cleaned up, screwed together with a temporary crown on it. It's a beauty.

There's a slim chance of me conceding on this one and taking it to my watch guy, in part for some of the reasons mentioned in this thread!!

Screenshot_20180929-195516.png

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Khan
      Stem broken - can it be rescued?

      By Khan · Posted

      Hi I got a Jaeger LeCoultre K911 movement, where one of the stems was broken. Part no. Should be 401.  Im based in Europe and tried Cousins but its discontinued. They except to get stem in stock for cal. K916 but will that work? Or Is there a way out to join the ends?
    • Bonefixer
      AS2063 - hand setting

      By Bonefixer · Posted

      The part was how it fell out of the movement - the train wheel bridge wasn’t screwed in.    I’ll probably dismantle the part, if I can, to work it out.    The train of wheels ran fine - it was only once the keyless works were installed I noticed the problem. 
    • mthomas828
      Balance staff sourcing?

      By mthomas828 · Posted

      Hello, I am about 5 months into watchmaking and I love it!   The attention to precise detail is what really attracts me to it. (and the tools!) I am working on a 16 jewel 43mm pocket watch movement.   There are no markings besides a serial number (122248) .  The balance staff needs replacement. The roller side pivot broke off.  I successfully removed the hairspring using Bergeon 5430's.  I successfully removed the roller using Bergeon 2810.   Did i mention I love the tools?! I removed the staff from the balance wheel using a vintage K&D staff removal tool  with my Bergeon 15285 (that's the one that comes with a micrometer adjustment so it can be used as a jewel press as well as a traditional staking tool...it's sooooo cool...sorry..  can you tell i love the tools?) No more digressing..  I measured the damaged staff in all the relevant areas but I have to estimate on some because one of the pivots is missing. A = Full length  A= 4.80mm  (that's without the one pivot...if you assume that the missing pivot is the same length as the other pivot (I'm sure it's not)  then A = 5.12 mm...(can I assume 5.00mm here?) F=  Hair spring collet seat  F=  .89mm   (safe to assume .90 here? .. I am sure that my measurement's would at least contain  .01 mm error ?) G = balance wheel seat  G = 1.23 mm  (1.20mm?) H  =  roller staff  H =  .59mm  (.60 mm?) B  = bottom of the wheel to roller pivot   B  = 2.97mm  (3.00 mm?)     here I am estimating  again because this pivot is missing. So my friends, and I thank you profusely,  can you point me in the right direction as to how to proceed? Do i buy individual staffs?  or an assortment?   Since I don't know exactly the name of the manufacturer, will that be a fatal hindrance?   Tbh, I'm not even sure what country of origin this movement is. Thank you!    
    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      Thats why i asked that question earlier, what happens if lubrication is placed directly on top of epilame ?  As opposed to walled within its non epilamed area . I'm not saying its right, i have no idea , just asking questions. 
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      thinking of where epilam should be removed did you know there was a patent that covers this? At least for the escapement I'm attaching it. GB1057607A-1 epilame.pdf
×
×
  • Create New...