Jump to content

Dust: The Thing I Find Most Annoying About Working On Watches

svorkoetter

By svorkoetter
in Watch Repairs Help & Advice

 Share

Recommended Posts

svorkoetter WRT Addict

svorkoetter

Posted
Posted

The thing I find most annoying and frustrating about working on watches is putting the watch back together without getting any dust on the dial, hands, or underside of the crystal.

A few nights ago, I noticed a smudge on the rehaut of my Black Bay homage. How that escaped my notice when I first built the thing I will never know, but I finally decided to open it up, clean the rehaut, and put the watch back together. Should be a quick 15 minute job, right?

 

Well, I disassembled and reassembled that watch at least half a dozen times before I had it clean. Every time I'd put it back together, I'd notice something that wasn't there the previous time. A speck of dust or two on the dial. A speck of dust or two under the crystal. A very small fibre stuck to the second hand. "Rodico prints", where the areas where I'd removed dust specks from the crystal were now clearer than the rest of the crystal.

 

All of this is made more noticeable by the fact that the dial is almost black, and the crystal is domed on top and flat on the bottom, thus magnifying anything visible on the dial. A light coloured dial under a flat crystal would probably be a lot more forgiving.

 

My workshop is in a relatively clean, dry but not too dry, semi-finished basement room. My workbench is clean. I am clean.

 

Is there a secret to keeping a watch dial and crystal clean during the time one spends reassembling it?

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

When I'm casing a watch I check the crystal for dust while holding it over a piece of black cloth. I keep the cloth in shadow and only let light shine on the crystal, I find this most effective. Once I determine the crystal is clean, I keep the face case up and place it over the movement. This greatly decreases the chance of dust getting on the inner face. Regarding the dial, I just give it a good blast with my puffer and check it very carefully with a loupe.

Link to comment
Share on other sites
mwilkes WRT Addict

mwilkes

Posted
Posted

Feel your pain. Had the same problem last night - disassembled/reassembled three times. PITA.

Wondered if having something nearby that attracted dust with static - maybe a balloon or something - might help...

And Rodico...anyone else tried the 'premium' stuff? I think it's terrible - leaves smudges waaaay more than the blue stuff!

Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted

Mark says the same and he is a pro! The premium Rodico is no improvement over the regular one! Have you guys tried to demagnetize your movements before and after cleaning? Mark recommends it too. Also, tweezers and screwdrivers have to be spotless clean and the location you work free from drafts that may bring in dust (no matter how clean the surroundings may be). I also use surgical gloves, lint free/static free "work" clothes and keep my blow pump handy and use it very oftem along with the Rodico and other stuff as needed.

 

I keep my stuff pretty much like if I was working in a clean room (which I did briefly a long time ago). That's one reason I don't take too many pictures of my work...I don't want to bring anything inside my area that is not essential...of course there is some flexibility, as I said almost like a clean room. Sometimes I'm a little careless and have to work 2 or 3 times as hard...and I hate doing that!

Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted (edited)

The premium stuff is white in this parts but who knows elsewhere since the regular one here is a greenish-blue greyish whatever color but more into the blue than the other ones...and becomes almost white when stretched and very dirty for mostly nothing.

 

And of course there is a stronger coloured "rodico" type of putty from A*F that is trying to compete, cheaper, but I haven't hear many people talking about it. Mark doesn't like it either which is something to mind.

Edited by bobm12
Link to comment
Share on other sites
PadraicB WRT Addict

PadraicB

Posted
Posted (edited)

Same here guys !   I'm very fussy about dust & debris inside a watch, I use plenty of puffer air & avoid wearing nylon clothes, carpet slippers, etc, that attract static.

 

And rodico ...  isn't it just blue-tac by another name ?

 

It's not blu-tac - rodico feels more like a lightly sticky clay while blu-tac is a very sticky plastic-like material. I also doubt blu-tac has anything like rodico's absorbency.

 

The Bergeon rodico I'm using (which is NOT the premium variation also from Bergeon) is a light green colour.

Edited by PadraicB
Link to comment
Share on other sites
noirrac1j Distinguished Member

noirrac1j

Posted
Posted

I wear nitrile gloves during and after cleaning and during assembly, and change them out to a fresh pair just before recasing. I rodico my screwdrivers, blow the crystal and case with air from a pressurized canister,and look at everything with high intensity LED lighting and 3.5X visors also with LED--Yeah, I consider myself a normal amateur. 

JC

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • HectorLooi
      Battery

      By HectorLooi · Posted

      Try putting everything back together and closing the back cover. I think one of the two springs has to contact the metal casing to ground the casing. So when you press the button, it will touch the contact on circuit board and close the circuit.
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      Yes, the seconds hand is the longest and goes almost to the edge of the dial. I can’t quite picture it how you do it on the rubber pad
    • Murks
      Battery

      By Murks · Posted

      A don't think so it leaked or damaged it because the watch itself works it just the buttons ain't working not connecting with the circuit board have taken more pictures of where the buttons makes contact with the circuit board.
    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      I think what peter means oh is once he has fitted the hands and  checked for  alignment if them and that they dont foul, how does he then hold the movement to remove the stem in order to case up. The dial cannot be laid on a cushion or in a movement holder as the hands will get damaged. This can be quite tricky for a beginner, what i do is  to stand the movement on edge on a rubber pad so it doesn't slip. Hold the top edge with one finger then my dominant hand uses 3 fingers to press the stem release and flick out the stem. See below peter, leave off the second hand as this is the longest and gets caught the most, then fit it once the stem is out. Alternatively place the movement in one of the cup style holders, i imagine this is what they are designed for. They only touch the very edge of the dial.  
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      Yes I understand that. What I’m asking is, after the hands have been fitted, it’s been checked that the hands do not touch etc. then I need to remove the stem to fit the movement in the case. I have the push type, I need to turn it upside down and push the setting lever post and pull the stem out. But of course the dial and hands are in place and I have a glossy dial with lume dots and I do not want to cause any damage while it’s upside down pushing on the post of the setting lever.
×
×
  • Create New...