Jump to content

Making a Balance Staff


Recommended Posts

Need to make a balance staff for a European picket watch. The old staff had both pivots broken off. First I disassembled the watch and removed the balance staff. Removing the roller table was the hardest part because it was a Three arm balance and my Magic Roller Remover would not work so I used the scissor type.6747fe43a99bd188eacf952d9fef8dac.jpge7e75d9c69e9a769a9ad6711e9c6b4a6.jpg1fa88274beaa1d13932d30eec2514bed.jpgc078f7e520c6a346dfadcaff67cec649.jpg30f532e8ae4870da44c7cbcaa0281ed8.jpg1e2a163391ea846c35b2b298187f5b07.jpg844d0cfbd16fab2a941d595c66400080.jpg

I then determined the widest diameter of the balance staff and found a 2.0 mm piece of Blued Steel. I cut off 1 inch and sized the collet, and inserted in into my Boley Leinen Lathe. I then started to cut the Balance and Hairspring side by first using the old staff as a guide and marking the piece of steel with my carbide graver.84d1245e54d14e9c32e366e831d56e88.jpga8d59714009b2c8e9837c7d0a23a9576.jpg

I started cutting down the first diameter where the balance fits and simply cut and measure until it was snug but still room to stake it in place. I then cut the hairspring diameter next and fix and cut repeatedly until it was snug. I used a special gauge to measure as I went along. Once the part fit was good I worked on the pivot with the graver until I got it down to around 0.2 mm and then used a stone to get it to around 0.14. The rest I plan to do on a Jacot tool.0674a45da0908e5666cce3fe60dacaea.jpg5f5da6c0d5a8c8836f329b4007570fd4.jpg974ed69f2161befa35058fb02420bf8f.jpg

I then flipped the part around with a different collet and started working the Roller Table side using the same technique. I Amos finished off the plate where both the rolled table on one side and the balance on the other side rest.7f9288040022be85fb24dd8435190d3d.jpg

Slight error in the description. I left the full part in and started working on the roller table side before cutting off the part and flipping it around...saves time.fef5e1e9bedb5099cc57df61d48dd29c.jpge35b6f93179d1155af32162d51002e0d.jpg69dcc763d9f12d137ec285e3e6e5a2d8.jpg73865aa95c3ce5477a81ab5860cefa62.jpgae5f5dd2ca1ac1eaceaf541f66d0e1c0.jpg

I worked on the other pivot as well and got it down to 0.14 with a graver and then a stone...on the Lathe. The final product looked great. I am waiting for a set of vintage pin gauges to get the pivot size exact. Will finish it off next week.bae231293c9eefa9bb05910589d5ce6d.jpg13be0555c60fc6945650f2f963450b71.jpg

 

 

Sent from my iPhone using Tapatalk Pro

  • Like 8
Link to comment
Share on other sites

More progress. As well, made a video on how to use Jewel Hole Gauges. So I staked the balance wheel onto the newly made balance staff, friction fit, and it fit really well. Very pleased . I then used the jewel hole gauges to determine the hole size and this the pivot size. Turned out to be 0.10. Now I need to burnish the pivots to that size, fit the part in the movement and once fit perfectly, I will add the rolled table and the hairspring.



c26c2fd09d942f352dc3ca471539cc6a.jpge9e49f4d49e75f1966a590b151902e4c.jpg



Sent from my iPhone using Tapatalk Pro
  • Like 1
Link to comment
Share on other sites

Also lined up the impulse jewel to the center of two arms and then drew the line straight from the jewel to the pallet fork pivot then placed the hairspring on the balance loosely to align with stud; while the impulse was perfectly centred with between the banking pins.


Sent from my iPhone using Tapatalk Pro

  • Like 2
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • When faced with say a pocket watch bridge which is cracked, silver soldering to repair is often the only option (hopefully someone wasn't there before hand with soft solder). I can generally do this succesfully and tidily with a small torch and miniscule pieces of silver solder, but on parts which were mercury amalgam gilded the heat can have have a deleterious effect on the finish.   I keep wondering if there's a good way to refinish these - and despite having the needful items would rather avoid using the mercury process.   In the past for electronic work I've gold plated PCBs but this involved gold potassium cyanide solution, which also doesn't realy belong at home. I've read that there are now safer alternatives but couldn't find more detail (and importantly how similar are the results to amalgam gilding, since I wouldn't want to refinish the whole watch). Pointers would be very welcome (and yes, I know solutions containing gold won't be cheap!) Alan
    • The first one is an Unruh max stake for pushing out staffs
    • Ok so with the great answers for my previous question may I ask what these two attachments are used for. The one with the red knob is I assume used for hand setting the seconds hand? Jon      
    • According to Cousins site I need to look at document G22 as I think I need an ATGB at 304 but I cant find this size in G22 doc. The last thing I want to do is order the wrong one😳  Unless I cant see the wood for the trees 😆 I could be looking at the wrong style, I assume its classed as Round plastic Armed  https://www.cousinsuk.com/product/wide-ring-gold-atgb
    • When building a new Watch I have tended to use a file to remove the remnants of dial feet that are not needed as many dials come with four feet to accomodate different movements, but this can be a bit messy so now I use this with a great deal more precision as you can use an appropriate bit for the job and keep it very localised.      
×
×
  • Create New...