Jump to content

Does anyone love Seiko Divers as much as I do?


Docbondo

Recommended Posts

They are fantastic divers watches ,Seiko have always offered good value dependable watches and I have quite a few in my collection both quartz and automatics, the only fly in the ointment with Seiko as a company is there tendency to change models and designs like I change my socks this can make it impossible to get case parts, bezel inserts or bracelet links for even very recent models because no one carrys the spares because Seiko dont produce them once a model is dropped from the range.

Link to comment
Share on other sites

  • 2 months later...

Nothing wrong with a Seiko diver (or any other Seiko pretty much!). And spares can often be found, although they do take some finding at times, the divers are normally pretty well covered. Although to be honest I’ve been looking for a chapter ring for a 7A28-702a for about two years now... one will turn up one day I’m sure (I hope).


Sent from my iPad using Tapatalk

Link to comment
Share on other sites

  • 1 month later...

I have a Seiko diver. It's a fairly early XKS007 being manufactured in October, 1997. My experience with it has been generally good and it kept excellent time prior to suffering a mainspring mishap. Repairs are pretty simple with that model though. Oddly enough in my case, I prefer mechanical watches for my divers. I have more than a few quartz watches for other daily wearers.

Link to comment
Share on other sites

  • 2 months later...

Well let's see those Seiko mods folks!! Replaced the original 7S26 movement with a 7S36 due to failure of the original after 22 years with only one maintenance. My bad! New aftermarket hands with Super-LumiNova, custom coin edge bezel from 316L stainless steel, green aftermarket insert and a new double seal crown. Lots of fun with this one.

SKX2_50.jpg

Edited by TexasDon
spelling
  • Like 2
Link to comment
Share on other sites

I do love a Seiko currently I have 2 in my collection a 1978 (not a dive watch)

46969151971_55f449a8fd_b.jpg

and a Japanese 007 seen here chillin in the snow, it came to me as a 'non runner' but actually all it was missing was the plastic ring that holds the movement in place! I got a new one from Cousins and it doesn't miss a beat!

47167658631_bc84966ccc_b.jpg

 

 

  • Like 3
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • No real question here, I managed to clean and reinstall this straight. But I just thought I would share this silly design for a balance cap jewel on an old Junghans pocket watch caliber J32. The screw is in the center, the jewel eccentric; the opposite design from every other cap jewel I have ever seen. But it has no steady pins beneath so tightening the screw means the cap jewel wants to rotate away from the hole jewel. Without an automatic oiler, this took about 6 tries to oil and screw down the cap without spinning it away. A tiny bit of Rodico didn't really help. Happily they don't make them like this anymore.
    • Thanks for your most appreciated assessment with this. I will purchase a new movement. 
    • Sorry I am confused by step 4. Which screw? There is the balance cock screw. I don’t think that is what you are talking about. The only other screw I see is on the side of the swan neck regulator. I do t think that is the one you are talking about either Well I managed to make it worse again but I could take pictures.  I had put the balance cock partially in place with one locator pin in. I wanted to remove it and I know I should use my screwdriver in the slot to move it off the pin but I didn’t l pulled wit my tweezers and it stuck then gave suddenly and was thrown a few inches away and of course the hairspring got tangled (a coil was above the cock) and untangling it from the cock deformed it.    I am going to try to put it back in shape and I will likely post more pictures after shortly. I’ll wait for feedback before reattaching it to the cock I am sorry I think I’ll give up. I was trying to remove the tangle. I had previously succeeded but now I just made more of a mess with this new tangle.  Lf you see my spring it is now just a knot.  Let’s keep a positive attitude. The movement was already broken. It was working but couldn’t be used. So what if it can’t run anymore… I went on and reinstalled the mainspring in the barrel by hand and managed to put the arbor back in.  Now I need to close the thing!  
    • Hello and welcome from Leeds, England. 
    • OK, bad video... Almost all of them are. To attach the spring (stud) to the cock: 1. Put the cock on the table top upside down.  Open the regulator if closed. 2. Put the balance on , align the stud above the hole for it in the stud carrier. 3. Help the stud to get in the hole by gentle pressing. 4. When it is in, grasp the cock with balance with tweezers (from aside, not from above), then get it between fingers, not changing the horizontal position, then tighten slightly the screw. This is the moment to correct the high position of the stud - it's top must be even with the carrier. Now tighten the screw. 5. If the outer coil is out of the regulator, move the regulator to the max to '+' position, then guide the spring to get in the regulator. Now You can return the regulator where it was and close it above the spring
×
×
  • Create New...