Jump to content

First watch

p2n
 Share

Recommended Posts

p2n WRT Addict

p2n

Posted
Posted

As I mentioned in the intro post - have decided to try my hand at watch repairs - as a hobby only.

I had a poke about and found one guide that contained this useful piece of advice: "You'll almost certainly break the first movement you work on so don't practice in the family heirloom!" Seems reasonable so I bought a "not working" mechanism from ebay for £6 to have a go on.

My goal: take it apart and rebuild it without breaking it or making it any worse than it started.

I almost managed it as well :D.

I checked I'd let the tension out of the mainspring by lifting the clicker and gently rotating the winder - it seemed to be full let down. It wasn't - it was just stuck. So when I started removing the bridge over the gear train it decided to let go. As a result I lost the minute hand.

Other than that I managed to disassemble and then reassemble the watch without further mishap. While apart I had a look at the mechanism in closer detail. The hairspring is broken and a little mangled and the balance jewel is cracked. Probably not fixable (let me know if it can be done with limited tools), but that's not why I bought the thing in the first place.

Not sure what make it is either.

 

Anyhow - that was #1. I've attached some photos I took - meant to take more during the process but got a little absorbed and forgot.

On the lookout for movement #2 ...

 

 

2018-03-01 17.47.25.jpg

P3010031.JPG

P3010032.JPG

P3010033.JPG

P3010036.JPG

s-l1600b.jpg

s-l1600d.jpg

Link to comment
Share on other sites
anilv Distinguished Member

anilv

Posted
Posted

Thats a nice watch! Not exactly what I would have recommended but for 6pounds its ok. The dial is in pristine shape, try to find the missing hand.. if this hobby develops you may have skills in the future to bring it back to life.

A better bet would be a Seiko or Russian watch (raketa is good) which can be found in running condition on the net. Problem with dead watches is you cannot gauge your progress. If you start with a running watch and put it back together then you know you've got it right for the most part.

If you get stuck post on the 'watch repair help section' .

Good luck

Anilv

 

 

Link to comment
Share on other sites
p2n WRT Addict

p2n

Posted
  • Author
Posted
6 hours ago, anilv said:

try to find the missing hand.

It's not missing in thats sense - I still have all the pieces :P. The suddent acceleration when the mainspring unstuck was a little too much for it.

To get it going I'm going to need a regulator, hairspring and balance staff jewels. I need to keep an eye out of ebay for spares for that movement I guess.

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Murks
      Pallet jewel

      By Murks · Posted

      Hi a have bunch pallets jewel here a want to replace it with a broken one how do a know witch is the entry stone or exit I know normally the exit one has a bigger locking corners ?
    • Jon
      Chinese clone demagnetizers

      By Jon · Posted

      I use on of these Eclipse demagnetisers. https://www.eclipsemagnetics.com/products/workholding-systems/table-top-demagnetiser/ I got fed up with those Mickey Mouse blue things and went industrial You can pick them up on eBay from between £70 to £100. They will demagnetise anything. I mean, anything, from a hairspring to a hammer head. The table is about 5 x 6 inches. You are not going to find anything close to being this good! It will demagnetise the biggest and chunkiest of cases with the movement inside. You'll never wonder again if your demagnetiser did the job.
    • nevenbekriev
      First Project Already A Bit "Sideways"

      By nevenbekriev · Posted

      Hi Dean, The solution with the alum for the broken screw is good and is generally used by watchmakers from many years, but You have to take off ALL steel parts from the plate. In some movements, the post for the minute wheel, for example, is made of steel. Deeping partly the plate works too, but some marks may left on the line where the solution doesn't cover the plate. Heating the solution is needed to accelerate the process. With the years, a rich collection of screws gathers and then finding the needed screw is not a problem. But till then it will be helpfull if You get some assorted screws lot. The other option is making screws. This is usually for the ones with specific form and sizes that doesn't meet often. But the skill of making screws is something that will never be unnecessary
    • Neverenoughwatches
      404 Club

      By Neverenoughwatches · Posted

      Haha yes you do have to reel in your bidding enthusiasm Michael. I use a " not enough time policy " to restrict myself or else known as sniper bidding. Decide what you are most prepared to bid and place it 7 seconds before the end, cross your fingers ,job done . The price paid here i would say was top  figure another day could have been $40
    • RichardHarris123
      Baum & Mercier

      By RichardHarris123 · Posted

      The question is did Baum and Mercier use that movement.  I know they used other ebouches. I  can't find any evidence that they didn't but that doesn't mean they didn't. 
×
×
  • Create New...