Jump to content

Watch band replacement and movements

mikecj

By mikecj
in Watch Repairs Help & Advice

 Share

Recommended Posts

mikecj Member

mikecj

Posted
Posted

All,

A few questions.

1. What are the spring loaded bracelet type watch bands referred to in the industry. I'm trying to find replacements and do not what yto refer to.

2. I am looking for a Seiko 5P30A movement or suitable replacement.

3. Similarly, Pulsar Y563A or a replacement.

Thanks, 

MikeCJ

 

Link to comment
Share on other sites
mikecj Member

mikecj

Posted
  • Author
Posted
4 hours ago, Chopin said:

Are you talking about Fixoflex bracelets ? Some call them stretch bracelets as well.

fixoflex21.jpg

Chopin.

Thanks for the quick reply. Below are two views of the same watch. The bracelet ends nearest the watch reside in rectangular holes approximately 18 mm x 6 mm. They are equipped with coil springs allow the curved part to open enough allow the wearer to insert her wrist.

MikeCJ

0217181854a.jpg

0217181855.jpg

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Part swapper to part maker

      By Neverenoughwatches · Posted

      Next is to drill the screwhole this then provides an anchor point so the bridge doesnt slip around while scribing the shape. A cork lid, a pin and a piece of gaffer tape ( 😅 ) keeps it all in place. The hole is measured from the broken part using a hand measuring gauge. Mark the hole, punch it and drill it off to size. The awkward bit is working out where the jumper should be and the detent positions.  I remember watching a youtuber a while back do this with dividers, so i dug out my old school compasses and improvised a little. This bridge only has one hole and to find the detent positions you need two points of reference, so i just worked the second point from one of the corners, hopefully its near enough. Then scribe in the jumper using the two detent positions ( wind and time set ) that were marked and a big picture of the complete spring to look at that helps to give you a feel of where the jumper should be. 
    • ManSkirtBrew
      Seitz Tool - Help determine if Seitz or not

      By ManSkirtBrew · Posted

      Right now I'm making do with a similar micrometer (the one below is $45 shipped but you can find better deals) and a $20 stand. You do have to be excruciatingly careful measuring jewels, since there's no table, but if you don't have the $500 to throw around, it's a nice option.
    • noirrac1j
      Watch of Today

      By noirrac1j · Posted

      As  I kid, I'd watch Godzilla stomping over buildings and cars and I'd think to myself: Tokyo is a really dangerous place to live... . Cool watch!!
    • Neverenoughwatches
      Part swapper to part maker

      By Neverenoughwatches · Posted

      Next one up an AS 554, looks like a bit more to this one. First job is to check thickness, most springs are somewhere between .3 and .4, this one measures .35, that matches in with the .4 spring steel i ordered. So for marking up a permanent marker comes in handy to colour up the steel to be marked later with a scriber once its dry. Bestfit provide the extra bit of info for the jumper spring that is missing.
    • Hawaiikook808
      Seitz Tool - Help determine if Seitz or not

      By Hawaiikook808 · Posted

      Thanks again, Marc.  Super helpful. I was wondering what the hole was for, and now it makes perfect sense. With your help and the other members here, it looks like I'm good to go with my Seitz tool set. I had to order some replacement pushers, but with those, the set is complete and in good condition. Now, I need to figure out what tool to buy to measure jewels (amongst other watch-related parts). I had my eye on the JKA Feintaster micrometers, but people get crazy bidding on them for $400-600 USD. I was thinking of just a regular digital micrometer (Mitutoyo). Thoughts?  Mahalo. Frank      
×
×
  • Create New...