Jump to content

Omega dial


antonyh

Recommended Posts

Well i could`nt resist it another Omega that needs to be done up, i won`t go into it all.

The picures are not the best, but anyway dial as it arrived,

dial after i cleaned it up just to see what it looked like, with another set of tempary hands, awfull i know.

i had polished the case up, to give it a bit of a shine, i was going to get someone to restore the dial, but prices have sky rocketed

the last few years.

so in a drunked state last night i thought i`d have a go.

omegabefore.jpg

 

 

Beforedial1.thumb.jpg.703f256319286f12dfc0f588ad45aeb0.jpg

 

 

 

Bluedial.jpg

 

Edited by antonyh
pictures wrong order
  • Like 2
Link to comment
Share on other sites

Hey, that's not bad, pictures a little unclear and I'm not certain what that dial was suppossed to look like, but I'd say I've deffinately seen worse dial jobs. what were your methods/paints? Did you remove the batons and logo or cover them somehow? 

Link to comment
Share on other sites

Well firsty, don`t do it after you`ve been drinking.

The hardest thing i had to get over was finding a spray paint with a fine spray of paint, i tried loads before i found one.

I just kept cleaning the dial, with thinners then i used a a brush to finish it.

i did not remove the batons, i just gave it a couple of passes with the can.

after an hour before the paint had fully hardened i just simply removed the paint from the batons.

Its not purfect but it makes it a bit more wareable than before, and its i know its supposed to have a black dial with delphine hands,,,,,,,,,,, one day..

  • Like 1
Link to comment
Share on other sites

Well It seems like you could always go back and re do it if you wanted to, the dial as it was looked pretty aweful in my opinion, though i wouldn't be surprised if someone disagreed with me I think most of us would agree that it had gone well past a 'patina'. 
 

Edited by Ishima
Link to comment
Share on other sites

Well i`ve done what i set out to do, i`ve changed the hands to something a bit more inkeeping ,i`ve filled in the end of the battons

with luminious paint as it should be , and i`m going to where it, ive since changed the seconds hand for a chrome one to match.

In the old days i would have had it restored, it its not worth the £200 + V Soni wanted last time i asked the to do a dial for me.

omegabluedial.jpg

Link to comment
Share on other sites

  • 2 weeks later...

Dial looks a bit stark, probably the lack of minute markers doesn't help.

I would experiment and try to have a cross hair to break up the dial. Either use a sharpie, or even scribe the croshairs into the dial back to the metal with a sharp blade.

My 2cents.

Anilv

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hello, I am about 5 months into watchmaking and I love it!   The attention to precise detail is what really attracts me to it. (and the tools!) I am working on a 16 jewel 43mm pocket watch movement.   There are no markings besides a serial number (122248) .  The balance staff needs replacement. The roller side pivot broke off.  I successfully removed the hairspring using Bergeon 5430's.  I successfully removed the roller using Bergeon 2810.   Did i mention I love the tools?! I removed the staff from the balance wheel using a vintage K&D staff removal tool  with my Bergeon 15285 (that's the one that comes with a micrometer adjustment so it can be used as a jewel press as well as a traditional staking tool...it's sooooo cool...sorry..  can you tell i love the tools?) No more digressing..  I measured the damaged staff in all the relevant areas but I have to estimate on some because one of the pivots is missing. A = Full length  A= 4.80mm  (that's without the one pivot...if you assume that the missing pivot is the same length as the other pivot (I'm sure it's not)  then A = 5.12 mm...(can I assume 5.00mm here?) F=  Hair spring collet seat  F=  .89mm   (safe to assume .90 here? .. I am sure that my measurement's would at least contain  .01 mm error ?) G = balance wheel seat  G = 1.23 mm  (1.20mm?) H  =  roller staff  H =  .59mm  (.60 mm?) B  = bottom of the wheel to roller pivot   B  = 2.97mm  (3.00 mm?)     here I am estimating  again because this pivot is missing. So my friends, and I thank you profusely,  can you point me in the right direction as to how to proceed? Do i buy individual staffs?  or an assortment?   Since I don't know exactly the name of the manufacturer, will that be a fatal hindrance?   Tbh, I'm not even sure what country of origin this movement is. Thank you!    
    • Thats why i asked that question earlier, what happens if lubrication is placed directly on top of epilame ?  As opposed to walled within its non epilamed area . I'm not saying its right, i have no idea , just asking questions. 
    • thinking of where epilam should be removed did you know there was a patent that covers this? At least for the escapement I'm attaching it. GB1057607A-1 epilame.pdf
    • Back home...printing now.  Will report results
    • Oh well, if Master @nickelsilver says it's the way to go, then it is the way to go! I stand corrected! 🫡 Are there any other places where you're supposed to remove the epilame from the contact point of rubbing? I don't think so! Thanks for the effort @Neverenoughwatches, much appreciated! 🙂👍
×
×
  • Create New...