Jump to content

Wittnauer crystal wrench

UrgurTheGurgur

By UrgurTheGurgur
in Tools & Equipment

 Share

Recommended Posts

UrgurTheGurgur Member

UrgurTheGurgur

Posted
Posted

After repairing and servicing my father's great grandfather's Elgin pocket watch(picture heavy post coming of this). I returned it to him this past Sunday as an Easter gift. After dinner, he handed me his uncle's 60's Wittnauer Automatic which hasn't run in years and asked if I could take a look.

The caseback is stamped "Use All Proof 1200 Wrench" From what I gather, it is a tool which compresses the crystal so it can be lifted out. But try as I might, I cannot find an "All Proof 1200“ wrench. I did manage to find This tool on the Bay. Can anyone tell me whether it will work on this Wittnauer?

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

If you have one of these little monkeys you could try it. This tool is a must for anyone repairing watches. There are many tools for removing glasses. Many years ago many makers would bring out there certain tool for opening their watches, I had many,  this universal tool was better then most.

159.102.jpg

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted
28 minutes ago, clockboy said:

If purchasing one DON'T buy the cheap Chinese  version they don,t work. Purchase the Bergeon made one.

Thanks clockboy the cheap Chinese ones weren't about in my days. I see a lot of Chinese watch tools on ebay and they don't look very good.  

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted
1 hour ago, oldhippy said:

Thanks clockboy the cheap Chinese ones weren't about in my days. I see a lot of Chinese watch tools on ebay and they don't look very good.  

I did have a Bergeon lift tool but at the time was struggleing with low domb crystels so purchased the Chinese one to see if it would work better. However I just found the build was crap & just did not work yes I suppose I could file & dress the claws but what a per larva. As the saying goes you get what you pay for.

  • Like 1
Link to comment
Share on other sites
UrgurTheGurgur Member

UrgurTheGurgur

Posted
  • Author
Posted

Thanks for the advice, guys. I'll definitely be keeping an eye out for a used Bergeron lift.

As to the one I linked in my post. I just thought the Longines one might work for the Wittnauer. Because I believe Longines owned Wittnauer at the time this watch was made. But there is probably only one way to tell. Right?

Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted

And careful since a used -- or abused -- Bergeon could be worst than a new Chinese...they won't work, either one! And you will have to dress every claw risking to offset the "balance" of the tool. Still the construction may be better in the end with the used one...Always a gamble buying used, especially when they are not that cheap.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      That's the right technique Mal 👍 If you are ok with a loupe ( which I'm not ) then pick up the dial in your left hand and make a tripod holder out of 3 fingers and then exactly how Mal and me described with your right hand, press and flick out the stem at the same time. You need three fingers to do this, i use my ring ring finger , sounds like mal uses his little finger, just whatever you feel comfortable with. The key point and dangerous side to this is the tweezers or driver slipping off the release screw. Stablise your left arm by resting your elbow on your bench, so that you can hold the movement horizontally flat, use a x5 loupe to view  and good light so you can see well and have a good tight fitting screwdriver to push the release down. Or as suggested a pusher mounted solid upside-down somewhere then all you need to do is push your movement up to it. I'll rig something up in a bit to show you what i mean.
    • Neverenoughwatches
      Leaving the forum for a while.

      By Neverenoughwatches · Posted

      Thanks Michael, shes a real soldier, it would take a tank to knock her off her feet.  Shes surprised even me and i knew she was a tough cookie.  Good for you Michael, you keep at it. I've been reading your posts re. your watchroom they're inspiring and it doesn't matter how long it takes you to get there its about the journey. Rome wasn't built in a day, our watchcaves are our solitudes, our own little empires where we can shut ourselves away from the crap that goes on around us in the world. I look forward to seeing you progress, I have my own ideas how i like to do things. But in answer to your questions on that thread, just let your workspace evolve around you and how you work. You wont figure it out straight away but you will know when to change it and when to leave it alone. But most of all just enjoy it.
    • Malocchio
      Stem removal after fitting hands

      By Malocchio · Posted

      That can be tricky. Sometimes I hold the movement from the edges in left hand and with right hand I push the release with tweezers and simultaneously pull the stem out with right hand pinky or something. 
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      I see what you mean. I must admit I’m not entirely comfortable with that but I can’t see a better method than what you suggest. I’d like to see something like this mirror with a short spike: https://www.cousinsuk.com/product/mirror-for-observing-movements Place it on, push the spike on the post with one hand and release the stem with the other hand. Minor problem, it doesn’t exist.
    • Michael1962
      Leaving the forum for a while.

      By Michael1962 · Posted

      Hope you mum keeps on mending. I was adamant that I was going to get myself going after my stroke. I was only 52. I still have a lot of life left to live. Some people give up. Some people don't let it beat them. Your mum sounds like one of the winners. 👍
×
×
  • Create New...