Jump to content

Pallet fork not syncing with escape wheel

Reaz
 Share

Recommended Posts

Reaz Member

Reaz

Posted
Posted

Hello everyone, I am new to watch making and I brought a few junk watches to try to learn, repair and get them running again. I posted once before and I appreciate everyone's response.

However, I have gotten into a new problem again. This time this is with another Seiko 6309a and I just can't get it to run. The jewels of pallet fork does not engage properly with the escape wheel. Thus, the watch doesn't run. I really appreciate any help and I have added a link to the video of my issue.

Thanks!

https://youtu.be/HdLDZ4G1kkc?si=O3iR91dsPBwsJJYI

HectorLooi Distinguished Member

HectorLooi

Posted
Posted

The photos are a bit blurry. The pallet jewels ok. But I think the upper pivot looks a little bent. Could you get a sharper photo?

Check the pallet fork jewel holes too.

  • Like 1
rehajm Super WRT Addict

rehajm

Posted
Posted

I don’t see a pivot problem. With the 6309a I’ve had the enjoyment of the pallet bridge in place, everything looks correct while the fork is seated incorrectly. Something about that thin upper jewel as I recall…

…long shot- seiko low amplitude. Did you have enough wind? 

Reaz Member

Reaz

Posted
  • Author
Posted (edited)

I think the pallet fork finally sat in place randomly and got power. 

PXL_20240120_1655474242.thumb.jpg.8ded1adcbd5f4d949827fa00f2d07cb5.jpgPXL_20240120_1655179432.thumb.jpg.02016ff29e9bf2e815cecee96efe51d7.jpgWell, the watch is running. I really appreciate everyone's help! Is the watch from 1978 according to the serial 855656?

Again thanks to everyone, this forum is very helpful for someone new like me. 

(And excuse the mold on the dial. The person who sold this to me said it didn't run for many years)

Edited by Reaz
  • Like 2

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • JohnR725
      Oiling Dubois Depraz chrono module pivots (Omega Speedmaster Reduced)

      By JohnR725 · Posted

      I'm a little confused here before servicing everything was fine and now it's not? Then I'm assuming if you run it without the chronograph modular runs just fine or does it give you problems then? Then as far as tightening goes I've occasionally seen people use a staking set and sometimes it works sometimes it doesn't. You can also disassemble and flip it over that sometimes works. Otherwise try eBay and maybe one will come up. There is a tiny possibility if the Problem is on the gear part and not on the center tube that you could purchase a shorter version and pop it on your longer version that's a speculation on my part that may be that might work but if the tube itself is worn then you're going to have a problem then it's back to eBay and just try to find one in the first place all sorts of things will show up on eBay sooner or later.    
    • nickelsilver
      Gruen 330 balance complete

      By nickelsilver · Posted

      Why do you need a whole balance assembly (balance complete)? Staffs are readily available and cheap.
    • watchweasol
      Greetings from Whidbey Island.

      By watchweasol · Posted

      Hi welcome to the forum. Enjoy. dictionary_ebauches_sa.pdf TZIllustratedGlossary.pdf
    • Simeon
      Oiling Dubois Depraz chrono module pivots (Omega Speedmaster Reduced)

      By Simeon · Posted

      Righty ho, I re-serviced the chrono module and got a reasonable result with minimal loss of amplitude when not running the chrono and about 30 degrees loss when running. Great. The problem is now that the chrono (and movement) stops running after about a minute or so, a tap on the watch starts it running again. No issues with the movement running when the chrono is stopped. Going to service it yet again, obviously some residual issues with friction in the chrono module (Very frustrating - I wish there was some way of testing it as I go!) I also seem to have a problem with the cannon pinion where the movement is running continuously (with the chrono stopped) but it's losing significant time / stopping. This is one of those two piece ETA style with a driving wheel pressed over the cannon pinion, obviously arranged for driving the chrono module. I had no issues with this prior to service and just added a small amount of grease between the driving wheel and the centre cannon pinion as the technical guide required. What's the best way of tightening these up? I would like to replace it but I guess this is going to be hard to find as it is dedicated to the DD chrono movement. 
    • caseback
      Chinese tools debate

      By caseback · Posted

      He uses the micrometer cap, but he leaves the spring out (you can see that in the video). If you leave the spring in, the spindle will move up as well (as shown by @Knebo).
×
×
  • Create New...