Jump to content

Unusual radio-controlled wristwatch and why are there so few digital ones?


Recommended Posts

It has a very light plastic case with mineral glass, the engine room is almost empty, and the model is also non-existent. Unfortunately, I can't find the instructions anymore, not even the model itself. Brand: Majestic made in Germany. I completely disassembled the part, I don't remember why, but now I put a battery in and I'm trying to adjust it. First you have to push in the crown, then the watch runs quickly, to 12 digits and waits until it receives the signal and adjusts itself. Hour is set with the crown pulled, the hour hand always jumps one hour further, mechanically! (It wasn't right at first, then I compensated for the wrong values and then it worked, later it also worked with setting it to 12.) Can someone tell me more about the watch and the technology? The battery cover grips the crown with one arm and serves as a contact switch. Actually, it's all very spartan and technically impressively simple, I wonder which crazy engineer designed it all to let this model appear on the market for a short time.

---------------------------------

Then it occurs to me that there are only a few digital radio-controlled clocks, most of them have hands. So I wonder why that is.

--------------------------------

And the market is flooded with cheap jewelless watches, most with some standard movement. The question is how long do watches without jewels or with a jewel on this spindle with the magnet, the jewel sits where the flywheel/magnet sits.

2023-07-17-112036.jpg

2023-07-17-111939.jpg

Edited by Fischgott
Link to comment
Share on other sites

I can't tell you much about the movement, but my best friend works at NIST where the signal it uses to set itself comes from. He just designed/made/installed a new FPGA based server for that signal, and will be moving all the servers to his equipment in the near future. If you have something that uses the atomic clock signal, it goes through his equipment.

  • Like 1
Link to comment
Share on other sites

Nice detail, thank you, but this is not the source of my signal, mine is dcf 🙂 because my watch residents in Germany. See the locations worldwide: https://en.wikipedia.org/wiki/Radio_clock My watches get the signal in around 5 Minutes, i guess the dcf signal is sent every 5 or 10 Minutes or so.

And i discovered that casio has also G-Shock radio watches, and some unknown vendors have digital radio watches too, but i think they are all together overlooked somehow in my opinion. Casios watches can even process the signal from different stations worldwide. You dont have to adjust your watch every now and then, and the summer and winter time is also set for you by the signal.

Found this link: https://www.hkw-elektronik.de/produkte/empfangstechnik-am/pc-funkuhren/ very interesting. Looked up the letters on the pcb. Dont remember the internals exactly but this could be it: https://www.hkw-elektronik.de/produkte/empfangstechnik-am/funkuhr-und-steuermodule/ And the hours are set through metal disks and springs and a very unique lever.

Edited by Fischgott
Link to comment
Share on other sites

One of the problems with the all the clocks and/or watches that receive digital time signals is the problem of getting a nice clean reception.  Then the next amusements for me is what do they do if they don't get a nice clean signal?

5 hours ago, Fischgott said:

My watches get the signal in around 5 Minutes, i guess the dcf signal is sent every 5 or 10 Minutes or so.

What you typically find with these items is they do not try to receive continuously. Running the receiver continuously consumes a lot of power and watches typically don't have a lot of power. So usually what they do is they will attempt to synchronize from time to time like every 24 hours typically sometime after midnight when there's less interference. Even initially when you're setting the time on them or their trying to set the time they might ask you just give up for a while and then try later if they can't get a signal which means of course that your watch isn't on time.

Here's a link to the US transmitter.

https://www.nist.gov/pml/time-and-frequency-division/time-distribution/radio-station-wwvb

 

 

 

Link to comment
Share on other sites

I read up that within 2 minutes the watch should get the signal, i talk about a watch without time waiting for signal. Very interesting video: Amplify signal by hanging the watch over a metal tube: 

 

The perfect atomic wristwatch would be the F91W without any buttons. Always 24h mode, time in second, day of the week, day plus month, no other function. Thats it. There are only very big atomic digital watches out there, but very small atomic analoge watches. I cant get why. Also i prefer flexible stretch wristbands.

I also cant get why a watch has to be big, because its ugly, it gets in the way, its unkomfortabel, it clings everywhere. And then the "luxury" watches, watches for thousands of dollars with obsolete technology from before 100 years with a brandname. Is it because ones ego thinks: whooo im special

I also dont like the fitness features, its a waste of time, unless you are a maniac who destroys his body professionally.

Also the signal should be used as an emergency alert, so everybody gets awake in the night in case of a disaster.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Personally I would salvage the missing screws from some donor movement.  I also bought a random selection of screws "Assortment of Stainless Steel Watch Screws" for next to nothing.  As for using an Alum solution - I had great success with that removing a rusted stem from a stainless steel crown.  The best piece of advice I read on doing that was to keep the solution warm so that the reaction didn't take weeks!  I did it in a couple of hours with the solution in jam jar and the jam jar in a saucepan full of water which I left on an induction hob maintaining about 60C in the Alum solution.
    • I decided that it was time to tackle the piece that I'd set aside as my first project. The subject in question is a Gruen Veri-Thin pocket watch.  It winds and "runs".  On the time grapher, it has reasonable amplitude (240 or so depending on the position), but was loosing close to a minute a day.  The stem also has the annoying tendency to just come out when pulled, which makes it super hard to set the thing.  As with many things this one started sideways and just got more so.  I was able to overcome the mangled "tab" on the back case cover (a well placed, very sharp knife enabled me to get in when I couldn't get a purchase on the mangled tab with a case knife.)   I was then sort of shocked to find that one side of the dial was held down with some sort off tape or adhesive material as someone had broken the dial foot screw on that side and left the broken screw in the mail plate. The loose stem does in fact seem to have been a poorly tightened setting lever screw, but I'm afraid there may still be gremlins in the keyless works.  While I was able to get the stem to stay in by putting everything in the right place and tightening the setting lever screw (before I took it all apart for cleaning and inspection), it just didn't seem to all sit right. The final gremlin showed up when I was taking off the lower cap stones for the balance and escape wheel (yes the Gruen 380 seems to have a cape jewel on the escape wheel).  The balance stone came off fine (but that in fact is the smallest screw I've ever seen.  When I turned the movement around to get the one off the escape wheel setting, I found that the screw head had been mostly sheared off.  After some reading and looking at what I had, I decided to try and tease what was left of the screw out of the hole by nudging what was left with the corner of my smallest screwdriver.  After 20 minutes or so, I was able to get the remains of that screw out. The picture I'm including of the disassembled movement was taken before I got the second cap stone off, so in the picture, it's still attached to the main plate (for those looking carefully, you'll only see the one cap setting in the pic.) Now I'm left with: A broken dial screw inside the main plate that needs to come out A broken cap stone retention screw that I have in my parts tray, but that is strictly useless and needs to be replaced. The need to get another dial foot screw I'm contemplating solving the first problem by soaking the main plate in an alum solution.  I think the main plate is brass and shouldn't be affected, but I have not been able to confirm.  This seems like the easiest option as I can't really access both sides of the screw to use the pricey Bergeon tool (which I don't fancy buying unless I have to.) I have located a couple of donor movements and have questions out about whether or not the include the dial foot screw and prompting for pictures of the dial side so  evaluate the cap stone settings.  I've also found that a supplier in this country does have the cap stone settings, but isn't overly clear about whether the screws are included. Are these the types of things that one can scavenge out of assortments or is it best to just grab one of the donors assuming that they look like they have what I need?  
    • I visited this place last year just before they closed their counter service - amazing shop (filled from floor to ceiling!) and the guy that was working there was really knowledgeable and helpful!. Their website isn't as good as Cousins but I understand that if you fill out the contact form they have stuff that isn't on the site. https://gleave.london/mineral-flat-bottom-domed/
    • As always in this game the answer is “it depends “ because the first one worked out ok doesn’t mean all will. A case could be made in a way that it would not really matter much, sounds like your first example. However a case could also be made so that only a tension armoured crystal could be used. Generally you replace like for like to maintain the integrity of the watch.   Tom
×
×
  • Create New...