Jonno65 Posted June 19, 2023 Share Posted June 19, 2023 (edited) I bought a Westclox Boyproof Pin Pallet pocket watch a few months ago and found that the mainspring barrel was split. I managed to find another donor watch in which the barrel is good (also had no mainspring).. One of the shafts on one of the gears had moved too so it donated one of those as well. It's been sitting around because I can't figure out how to wind the mainspring into the barrel. The barrel arbor is integrated into the lid on the barrel and using that to do it by hand is nigh on impossible. Similarly hooking the end of the spring on the barrel and winding inwards is equally tricky. Is there another way without acquiring a large mainspring winder, or is one of those options the only way? I have attached a photo. Edited June 19, 2023 by Jonno65 Quote Link to comment Share on other sites More sharing options...
watchweasol Posted June 19, 2023 Share Posted June 19, 2023 Hi Which bit does the inner coil attac to ? The coil is to big for the fixed arbour but looks as though it fits on the brass wheel which then fits on to the fixed arbour. In which case try winding it onto that or making an arbour fitting into a pin. Vice and doing it that way.. a Single spring winder is around 50£ and you may only use it once.. a close up of both arbours attaching points ? Would be helpful 1 Quote Link to comment Share on other sites More sharing options...
Nucejoe Posted June 19, 2023 Share Posted June 19, 2023 I usually keep the washers that already wound brand new mainspring come in. If you can find a washer with ID equal to or a bit smaller than ID of the barrel, we then are in business. Hand wind the used mainspring inside the washer, like new ones are, next rinse the mess, spread a bit of oil on top of the coil, grease bareel wall. You now have your mainspring wound as a new one, ready to be pushed into the barrel. Hope this helps and good luck. 1 Quote Link to comment Share on other sites More sharing options...
Jonno65 Posted June 20, 2023 Author Share Posted June 20, 2023 13 hours ago, watchweasol said: Hi Which bit does the inner coil attac to ? The coil is to big for the fixed arbour but looks as though it fits on the brass wheel which then fits on to the fixed arbour. In which case try winding it onto that or making an arbour fitting into a pin. Vice and doing it that way.. a Single spring winder is around 50£ and you may only use it once.. a close up of both arbours attaching points ? Would be helpful The brass section is the arbor/lid combined. I have tried winding it onto that but the tension is too much to hold by hand, especially when attempting to insert into the barrel. There is a hook on the wall of the barrel as well which is a better option but still tricky and did mis-shape the bridle end of the spring and i'm super-cautious of not damaging it given I don't have a spare. 12 hours ago, Nucejoe said: If you can find a washer with ID equal to or a bit smaller than ID of the barrel, we then are in business. Hand wind the used mainspring inside the washer, like new ones are, next rinse the mess, spread a bit of oil on top of the coil, grease bareel wall. That sounds feasible. I could actually machine up something of the correct diameter - and slightly thicker than a washer which will help. I'll give that a go. 1 Quote Link to comment Share on other sites More sharing options...
watchweasol Posted June 20, 2023 Share Posted June 20, 2023 Hi if you have the kit making a tool to fit is the better option. Quote Link to comment Share on other sites More sharing options...
Jonno65 Posted June 20, 2023 Author Share Posted June 20, 2023 25 minutes ago, watchweasol said: Hi if you have the kit making a tool to fit is the better option. I do - I have a lathe. It hadn't occurred to me before (not that I had a lathe!) 1 Quote Link to comment Share on other sites More sharing options...
Jonno65 Posted June 24, 2023 Author Share Posted June 24, 2023 Just a little update on winding the Westclox mainspring. I machined up a barrel winder with a lead-in slot (didn't start out that way).... and I also had to use a pusher as well. It was still a bit of a pain as you have to line up the hook (bridle end for it to seat in properly. Anyway, done done and thanks for the tip! Pics attached. Now to rebuild the pocket watch! 3 Quote Link to comment Share on other sites More sharing options...
watchweasol Posted June 24, 2023 Share Posted June 24, 2023 Hi that’s a neat solution, what you have constructed is excellent and will probably used again. Very much like a standard watch spring winder only more robust, cost Time and brain power. Plus lathe . Great job. 1 Quote Link to comment Share on other sites More sharing options...
Jonno65 Posted June 25, 2023 Author Share Posted June 25, 2023 A good job - jobbed! Quote Link to comment Share on other sites More sharing options...
watchweasol Posted June 25, 2023 Share Posted June 25, 2023 Well done. A credit to you and your ingenuity. 1 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.