Jump to content

Hello! I just Completed a DIY Watch Cleaning Machine

twincityson
 Share

Recommended Posts

twincityson New Member

twincityson

Posted
Posted (edited)

Hi Everyone,

Longtime lurker on this site but I'd like to get more involved in this community as I've built up a couple years worth of knowledge as an amateur watchmaker.  I love tools, which is one of the many reasons I'm attracted to watchmaking.  I looked around at trying to purchase a L&R machine but was put off by the price.  Last week I decided I could build something suitable for my needs.  Previously I've been using a 3 step ultrasonic setup.  I give you my Frankenstein!  Total cost of the build was approximately $150 (not including L&R #566 and #3 Rinse) and includes a heated dryer function which works wonderfully.  It took approximately four hours to design/assemble.  I used an overhead stirrer and threaded the attached rod to attach to a tea strainer.  And yes, those are indeed cones cut down to hold the mason jars :).  Looking forward to participating in this community.

Here are the parts:

VONOYA Electric Overhead Stirrer w/ timer and speed controller

Amazon Basics 500-Watt heater with tip sensor disabled (6x6)

6 inch HVAC connector

3 mason jars (thanks wifey)

Soccer cones (thanks kids)

Gladicier brand tea strainer w/ misc lock washer and nut from Hardware store

BN-Link Indoor Countdown Timer (for heater so I don't burn the house down)

Old shelving cut down (thanks house remodel)

IMG_1752.jpg

Edited by twincityson
spelling
  • Like 2
Link to comment
Share on other sites
twincityson New Member

twincityson

Posted
  • Author
Posted

Thanks.  No reverse.  It'd be very simple to install a reverse switch but I'm not sure if it's worth it.  Just one more time I'd have to get up from my work haha.  Do you find you get better results if you alternate direction? 

Link to comment
Share on other sites
HectorLooi Distinguished Member

HectorLooi

Posted
Posted

The problem with a simple design like this is the spinning creates a vortex in the fluid. When the liquid is rotated, a vortex will form and all the liquid in the basket gets spun out and the watch parts inside are actually dry. 

Baffles and a downwards propeller were added to break up the vortex, and keep the liquid in the basket. Reversing the motor direction will also break up the vortex.

Looks like you will have to get up and do a bit more work.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Dmitry
      Eta 2970-1 rotor mount stops watch

      By Dmitry · Posted

      Here are the pics of the bridge. Looks correct, but as soon as I screw on the rotor, the watch stops. Video here: https://1drv.ms/v/s!ArG5E62RGctxjokY5ws85BzuJLVakA   Pics. Might have figured it out. I have been working on this watch for a while and since I got it as a non runner in a terrible shape, there was no guarantee that parts were proper. I think the main screw that was used on the rotor was too long, so it was stopping the main train. As soon as I fished out a much shorter and larger headed screw, things were good again. Please celebrate with me.  
    • KarlvonKoln
      B-Dip residue?

      By KarlvonKoln · Posted

      One-dip or naphtha should be safe, but are you sure it isn't magnetized?  I would also check that.  Although, if that balance is from an Elgin 760 0r 761, I would think it would have a hairspring of non-magnetic alloy.
    • Curare
      Spell Check

      By Curare · Posted

      Hi, Is there a spell check function available when you are posting ? Regards CJ
    • Curare
      Replacing armoured crystal in a front loading watch case…

      By Curare · Posted

      Hi John I just did a Seiko Lord-Matic a front loader without a split stem, I used a crystal lift to remove it, although I had to have it that tight I though I was going to break the lift before the crystal would budge. So I decided that the press would be a better option as I think crystals with tension rings resist a lot of compressing. I used a crystal press to repalce it and the bezel with no issues, obviuosly a different watch to the Omega. I just took my time and kept inspecting the installation progress bit by bit Regards CJ
    • Zendoc
      Replacing armoured crystal in a front loading watch case…

      By Zendoc · Posted

      Hello All, I’m replacing the crystal in an Omega Dynamic, # 165.039, which houses a cal 552, installed through the front of the case. The replacement Sterncreuz crystal is, like the original, with tension ring. I removed the crystal using a compressed air technique to pop it out.  (I have a crystal lift, but I’m always fearful of marking the crystal edges and so avoid using it as much as possible). Now to the replacement -  any tips on putting the crystal back in?  Am I obliged to using my dreaded crystal lift to complete the task, or how about a crystal press?  I’ve put lots of crystals in using a press, but never with the movement in the watch. The thought of using one with a front-loader makes me very nervous, with the fully assembled watch sitting under the press. How would more experienced folks proceed here? Any advice, gratefully received… John Down Under…
×
×
  • Create New...