Jump to content

Hello world!

brunomartins
 Share

Recommended Posts

Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
Posted
5 minutes ago, brunomartins said:

Hello!

I have been studying a lot about mechanical watches, watching videos and I have got really excited to begin some projects.

Believe or not, I am afraid of not knowing what screw goes in what bridge 🙂  

 

See you around the forum

 

Osvaldo Bruno

 

Welcome Bruno. You'll be fine fella. Plenty of good people here to help you. Keep the screws with the bridges you are taking off. Keep the bridges separate from each other .Take pictures and make of notes until you gain confidence and knowledge. Some recommend putting the screws back into their places after the bridges are removed. Personally i do think this a little risky, if not fastened in well enough when cleaning. But you'll find your own method for what works best for you. Any questions make sure you post some really good macro shots of front,  back, inside, case and dial as well. Any numbers letters and symbols are very important in establishing its make, manufacturer and calibre. Identification is required straight away as well as any history of the watch as well. Inc. anything you might have already done with it, repair wise or disrepair wise. Dont feel silly, anxious or intimidated in any way when talking to anyone about your questions, as one very respected member here often quotes, no question is silly. Everyone here has been where you are in their journey and we are all very helpful and friendly.  Enjoy Bruno

Link to comment
Share on other sites
brunomartins Watch Enthusiast

brunomartins

Posted
  • Author
Posted
6 hours ago, Neverenoughwatches said:

Welcome Bruno. You'll be fine fella. Plenty of good people here to help you. Keep the screws with the bridges you are taking off. Keep the bridges separate from each other .Take pictures and make of notes until you gain confidence and knowledge. Some recommend putting the screws back into their places after the bridges are removed. Personally i do think this a little risky, if not fastened in well enough when cleaning. But you'll find your own method for what works best for you. Any questions make sure you post some really good macro shots of front,  back, inside, case and dial as well. Any numbers letters and symbols are very important in establishing its make, manufacturer and calibre. Identification is required straight away as well as any history of the watch as well. Inc. anything you might have already done with it, repair wise or disrepair wise. Dont feel silly, anxious or intimidated in any way when talking to anyone about your questions, as one very respected member here often quotes, no question is silly. Everyone here has been where you are in their journey and we are all very helpful and friendly.  Enjoy Bruno

That was very encouraging and kind. Thank you and I have noted down your tips

Link to comment
Share on other sites
  • 2 weeks later...
grsnovi Distinguished Member

grsnovi

Posted
Posted

To get the best help with a specific watch you will need to provide photographs of the dial side of the movement without the dial attached as well as the bridge side often with a shot showing the balance removed.

Measuring the diameter of the movement can also help.

There will often be helpful clues in the keyless works configuration.

There can also be a stamped symbol showing the manufacturer of the movement (often under the balance) as well as a movement ID.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Knebo
      Epilame / Fixodrop

      By Knebo · Posted

      I did that also for a few movements - well, mainly in/around the train jewels. I made big efforts to epilame the mainplate WITHOUT getting Epilame into the Pallet fork jewels (where it's not supposed to be, right?). I made litte barriers with Rodico around that jewel and used drops from a syringe to apply on the rest.  However, I've now stopped doing this. For three reasons: 1. It's a hassle and consumes more of this liquid gold. 2. I didn't see the need when using HP1000/HP1300 lubricants and grease for most part. The two places where I'd use 9010 (i.e. escape wheel and balance) receive Epilame in specific places... or the cap-jewel-setting of the balance suspends the oil sufficiently be capillary action (see my "conflict" about using Epilame on the balance jewels).  3. Lastly, and here I really wonder about yours and others' experiences: I felt that applying Epliame to the train jewels left them looking hazy (borderline dirty) compared to the (painstakingly achieved) sparkly clean results of my cleaning process. I just can't help but think that the Epilame residuals would mix with the oil and cause more friction/wear. I don't know.    simple: it'll stay there. It won't move any further. That's exactly what is happening if you epilame a cap stone. You end up placing the 9010 right on top of the epilame and the oil will sit nicely on that spot.
    • Neverenoughwatches
      Coil for old Seiko Credor -- 4002920

      By Neverenoughwatches · Posted

      There are some parts on Ebay for the seiko 6020A, it may just be a waiting game for someone to strip one down, NOS will be more scarce . K would strip your movement down to the module then start looking at other seiko movement to see if that coil is used, then seek out a seiko part dealer. Also Retrowatches youtube owner Mike may give you some advice try him on his site . He also hangs around amateur watchmaking groups.
    • Waggy
      Setting lever spring

      By Waggy · Posted

      I would agree, in order to work harden something you need to exceed it's yield strength when it moves from the elastic zone to the plastic zone and you get permanent deformation and work hardening which is fairly close to its failure point, relatively speaking and dependent on the material/alloy of course. In theory you can load something constantly within its elastic range and not suffer work hardening issues.
    • Waggy
      Coil for old Seiko Credor -- 4002920

      By Waggy · Posted

      Probably easier to get a complete new movement - but CousinsUK list it as discontinued. Maybe someone on here knows a substitute movement ?
    • Kkramme
      Coil for old Seiko Credor -- 4002920

      By Kkramme · Posted

      Any other thoughts on how I can get a replacement coil? Any “hidden” or unknown physical shops (in Australia or elsewhere) that might have them in stock (but not always online)?
×
×
  • Create New...