Jump to content

Mido Ocean Star Powerwind oscillating weight and post

LittleWatchShop
 Share

Recommended Posts

LittleWatchShop Distinguished Member

LittleWatchShop

Posted
Posted

Another rookie mistake

I serviced this watch probably four months ago and put it on the autowinder (which some people have an aversion to!!).  While it timed out well on the bench, it was randomly losing lots of time.  It took a while for me to get the courage to open it up again--it is a front-loader requiring a special tool to remove the crystal...I have it...but it is a little scary to use.

Anyway, today, I opened it up and decided to check the upper and lower balance jewels.  The were fine, but I cleaned and oiled again.  Under the microscope, the pivots were perfect.

Then, by happenstance I noticed that the oscillating weight dragged against the balance.  Oh my!  When I removed the weight to check the post...it just came out!  I went back and looked at my disassembly pictures, and it had not come out during teardown.  A real mystery. How could this be...I will never no.

Fortunately, when I embarked on this job, I immediately found a donor on ebay...just in case.  Hey--this belongs to my old boss...the guy that hired me out of college some jillion years ago...a very demanding person.

Now I am waiting for the watch to run down and I will replace the bearing plate for the oscillating weight.

Is this a common thing for automatic winds?

IMG_8462.JPG

IMG_8464.JPG

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted (edited)
7 minutes ago, LittleWatchShop said:

Was it originally pressed in?
Was it staked in?

These two things are, as someone say, "the same difference" 🙂

'

Quote

Was it glued it?

Glue has (almost) no place in watchmaking.

Edited by jdm
Link to comment
Share on other sites
Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
Posted
37 minutes ago, LittleWatchShop said:

Well, what I meant was.  Put in and the kind of rivited from the other side.  I rather doubt that, but I am grasping at straws here.

Anyway, I hate this watch for several reasons.

Besides the mentioned LWS or were they enough. I would have thought the post was originally pressed in. Is it possible that the continuous winding from the watch winder in the same planes was too much and encouraged premature rotor bearing wear then causing an uneven pull on the post to eventually loosen it from its seating 😥.  Maybe a good reason not to use auto winders.

1 hour ago, jdm said:

These two things are, as someone say, "the same difference" 🙂

'

Glue has (almost) no place in watchmaking.

🥱 🤐

Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted
20 minutes ago, Nucejoe said:

Whatelse is there to wear out or break, its either the post or the bush in rotor. 

Seen broken ones quite often, not much can one do other than to repair or replace the broken parts.

My issue is that I just have not seen enough of these...experience counts!

Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

This type of oscilating weight is heavy enough to easily turn on the post even if unlubed, which causes wear on the post and the bushing. Thats another culprit with this design.

  In F4007N variant FELSA put jewels in the rotor instead of brass bushing, which came in 30 and 41 jewels version, those are real good winders, one would expect to see a culprit with the jewel breaking too often but I am yet to see a broken jewel in said  rotors.  

Best wishes

  • Like 1
Link to comment
Share on other sites
Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
Posted
17 hours ago, LittleWatchShop said:

Well, what I meant was.  Put in and the kind of rivited from the other side.  I rather doubt that, but I am grasping at straws here.

Anyway, I hate this watch for several reasons.

So nice when someone points something out that isn't especially helpful dont you think LWS . 👏

Link to comment
Share on other sites
LittleWatchShop Distinguished Member

LittleWatchShop

Posted
  • Author
Posted
39 minutes ago, Neverenoughwatches said:

So nice when someone points something out that isn't especially helpful dont you think LWS . 👏

Oh, @jdmcan be snarky from time to time, but I love him.  He has helped me a number of times!  And, it would be really hard for anyone to offend me on this forum anyway--it is my favorite hangout!

 

Link to comment
Share on other sites
Neverenoughwatches Distinguished Member

Neverenoughwatches

Posted
Posted
2 minutes ago, LittleWatchShop said:

Oh, @jdmcan be snarky from time to time, but I love him.  He has helped me a number of times!  And, it would be really hard for anyone to offend me on this forum anyway--it is my favorite hangout!

 

Its mine too if i had to be truthful. Ok It does wind me up though.  I dont feel it is necessary, its no effort to be kind and considerate,  just nice even, if neither of those then only civil at a push would be better than hints of sarcasm. Some folk would be far better individuals if they just chilled out and removed that wooded implement from up their waste disposal orifice. It means i can spend a lot more needed time learning and repairing instead of me having to mention it every time i see it 🤦‍♂️

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Khan
      Stem broken - can it be rescued?

      By Khan · Posted

      Hi I got a Jaeger LeCoultre K911 movement, where one of the stems was broken. Part no. Should be 401.  Im based in Europe and tried Cousins but its discontinued. They except to get stem in stock for cal. K916 but will that work? Or Is there a way out to join the ends?
    • Bonefixer
      AS2063 - hand setting

      By Bonefixer · Posted

      The part was how it fell out of the movement - the train wheel bridge wasn’t screwed in.    I’ll probably dismantle the part, if I can, to work it out.    The train of wheels ran fine - it was only once the keyless works were installed I noticed the problem. 
    • mthomas828
      Balance staff sourcing?

      By mthomas828 · Posted

      Hello, I am about 5 months into watchmaking and I love it!   The attention to precise detail is what really attracts me to it. (and the tools!) I am working on a 16 jewel 43mm pocket watch movement.   There are no markings besides a serial number (122248) .  The balance staff needs replacement. The roller side pivot broke off.  I successfully removed the hairspring using Bergeon 5430's.  I successfully removed the roller using Bergeon 2810.   Did i mention I love the tools?! I removed the staff from the balance wheel using a vintage K&D staff removal tool  with my Bergeon 15285 (that's the one that comes with a micrometer adjustment so it can be used as a jewel press as well as a traditional staking tool...it's sooooo cool...sorry..  can you tell i love the tools?) No more digressing..  I measured the damaged staff in all the relevant areas but I have to estimate on some because one of the pivots is missing. A = Full length  A= 4.80mm  (that's without the one pivot...if you assume that the missing pivot is the same length as the other pivot (I'm sure it's not)  then A = 5.12 mm...(can I assume 5.00mm here?) F=  Hair spring collet seat  F=  .89mm   (safe to assume .90 here? .. I am sure that my measurement's would at least contain  .01 mm error ?) G = balance wheel seat  G = 1.23 mm  (1.20mm?) H  =  roller staff  H =  .59mm  (.60 mm?) B  = bottom of the wheel to roller pivot   B  = 2.97mm  (3.00 mm?)     here I am estimating  again because this pivot is missing. So my friends, and I thank you profusely,  can you point me in the right direction as to how to proceed? Do i buy individual staffs?  or an assortment?   Since I don't know exactly the name of the manufacturer, will that be a fatal hindrance?   Tbh, I'm not even sure what country of origin this movement is. Thank you!    
    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      Thats why i asked that question earlier, what happens if lubrication is placed directly on top of epilame ?  As opposed to walled within its non epilamed area . I'm not saying its right, i have no idea , just asking questions. 
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      thinking of where epilam should be removed did you know there was a patent that covers this? At least for the escapement I'm attaching it. GB1057607A-1 epilame.pdf
×
×
  • Create New...