Jump to content

Calgary, Canada - New to trying to figure out watch repair for hobby only

CalgaryJim

By CalgaryJim
in Introduce Yourself Here

 Share

Recommended Posts

CalgaryJim New Member

CalgaryJim

Posted
Posted (edited)

Hi everyone, I’m very new to watches, bought a number of them this year so far and I have a late 1950s Tudor Oyster Regent from my father, I am thinking about trying to fix a couple of issues with it.

Edited by CalgaryJim
  • CalgaryJim changed the title to Calgary, Canada - New to trying to figure out watch repair for hobby only
grsnovi Distinguished Member

grsnovi

Posted
Posted

Welcome to the forum Jim!

If the Tudor is of sentimental value, I'd suggest that you at least become proficient on some other movements (possibly including a non-running Tudor of the same caliber).

Mark Lovick (our host here and YT personality) has some introductory courses that you might want to consider. In his Level 2 course he walks you through the disassembly, lubrication and reassembly of a movement that you can pick-up on eBay for $24 or so. It would be worth your while to consider his course and the ability to be hand-held through a complete tear down and rebuild where the end will almost certainly be a running watch.

oldhippy Distinguished Member

oldhippy

Posted
Posted

Thank you for your introduction and welcome to this friendly forum.

We all look forward to your contributions and continued involvement. 

  • 2 weeks later...

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • thor447
      Vintage Seiko lume pip technique

      By thor447 · Posted

      Very clever!
    • tIB
      Vintage Seiko lume pip technique

      By tIB · Posted

      Since I've learned lots here I thought I'd share a tip I picked up elsewhere and put to the test... For that 6105/6309 bezel lume pip look I've punched a clear plastic bottle of water, sanded it for the frost effect, removed the (smaller) pip from a standard/cheap replacement bezel, drilled it out to 2.5mm and fitted it using a smaller punch - fresh lume to hold into place.  Pressing into place is a bit awkward but you soon get the hang of it, and the end result is pretty decent I'd say... The worst part probably being the drilling rather than the pip!      It started out like this: 
    • tIB
      Seiko 6105 crown gasket service

      By tIB · Posted

      Ive asked this at a Seiko forum but I know there's plenty of experience here too...   As I have it the recently discovered servicing technique on these is that you stuff the crown full of gaskets and work it until the recessed washer pops, remove the washer, switch the gasket out, dish the washer and push it back into place, levelling out the washer in the process? First attempt did not go to plan... I tried using a plastic pusher to manipulate the gaskets in the crown... Wasn't strong enough and I was struggling to even get the gaskets in up until it broke.   Rethink consists of making/using actual tools: I don't have a staking set, so I've got the old man fashioning a metal pusher, essentially a 2.45mm OD tube with 1.6mm ID with a 6mm press the other end. Also got him on a dishing block/conical stake (sorry I'm terrible with terms) and a holder for the crown while I'm working on it...   I figure that's enough to do the process described above? Push with the metal pusher, dish the washer with the conical stake, press back in with wider flat press (drilled centre so it doesn't catch on the tap).    Plan is to stuff, press by hand and repeat? If that doesn't work by hand I've a drill press I could attach the pusher to for a little more leverage if needed. (Obviously I don't want to go too mad with that, and hopefully can avoid it altogether...)   Sounds like a plan? I'd welcome any advice here, since I really don't want to wreck a crown. Having replaced all the other seals though id really like to sort these too. I welcome any input/advice from those who have been there and done it... Thanks!
    • watchweasol
      Hello from Ottawa Canada

      By watchweasol · Posted

      Hello and welcome to the forum.  Enjoy
    • AndyGSi
      Make groove Case steel 316L - without lathe

      By AndyGSi · Posted

      You need to be more careful modifying the dial area. How does the bezel/lens fit on the front?
×
×
  • Create New...