Jump to content

Hello

Mason

By Mason
in Introduce Yourself Here

 Share

Recommended Posts

Mason New Member

Mason

Posted
Posted

Hello all - I am a new member here.  I hail from Idaho and where I live there are very few helps for watch collectors.  I have gotten in to learning how to change watch batteries on my quartz watches and really enjoy doing my own work.  I collect everything from cheapie quartz/solars  to mid-range expensive mechanicals  I am getting pretty competent on changing batteries without losing stuff or botching up the case/movements now still a bit hesitant to undertake anything too serious with my mechanicals, but would like to learn to do my own cleaning/oiling maintenance service one day.

Michael1962 Distinguished Member

Michael1962

Posted
Posted

Welcome to the forum Mason.

I am quite sure you will find a lot of experience on here as well as the courses run by Mark Lovick. Link should be on this page. Everyone that has done them have only good things to say.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • mbwatch
      Loose pinion

      By mbwatch · Posted

      Use probably the same key as you wound it with - on the end of the cannon pinion is a square that the minute hand is mounted to. You just need to turn the square, which will overcome the cannon pinion's friction and set the hands. That said, this could be the reason your wheel and pinion were separated and thread damaged. If the cannon pinion had been rusted or seized on and it was turned, it could have damaged the connection between the pinion and wheel. If it felt like your cannon pinion could turn on the center wheel arbor before and there is some grease under it, this should not be a problem.
    • dnhb
      Loose pinion

      By dnhb · Posted

      I've gone the threadlocker route having tried the material insert approach without success. The watch runs but I'm chary about winding it more than a turn or so in case the 'repair' gives way; still, there's an element of satisfaction in getting it going at all as it's a single bridge/plate design which I could only assemble dial side up & then flip over in order to be able to insert the 3 securing screws. The reassembly took a number of attempts over many hours but at least I got considerable manipulation practice & the experience will come in useful in future. I'm now faced with my ignorance about how to manually set the the time as this key-wound Waltham pocket watch doesn't have the usual pull-out stem facility. All I can think of doing is to adjust the regulator arm until it catches up with the current time & then revert to the central position.....
    • AndyGSi
      Omega Cosmic 2000 split stem question

      By AndyGSi · Posted

      So the crown should be a 0.9mm thread as you've ordered. How do you know the thread size is wrong if you've not removed the broken stem yet?
    • AndyGSi
      Where it begins

      By AndyGSi · Posted

      You'll need to be extra careful with the Citizen as Information along with Parts and Donors are pretty much none existing. You'll probably end up having to use a stem extender, that's hoping there's enough stem left in the movement.
    • Embezelled
      Where it begins

      By Embezelled · Posted

      Thank you! That's immensely helpful. I appreciate the trouble you've taken. The initial hiccup aside, I do hope to treat this watch with great care and respect. I've certainly learned one thing not to do, and also just the general need to start out very slowly and very carefully.    
×
×
  • Create New...