Jump to content

Cheap watch repair kit--review

LittleWatchShop
 Share

Recommended Posts

LittleWatchShop Distinguished Member

LittleWatchShop

Posted
Posted

I bought this kit to take with me when I am "junking" with my wife, so I can open a watch that I might find to see if it is worth purchasing, or perhaps to install a battery or some other small task.  Of course, I have a copious amount of quality tools, but do not want then to take them out of the LittleWatchShop!  So, since this kit is under $20 with tax and everything on Amazon, I bought it.  Here is my initial review.  A correction for the video: I paid $29 for the LG back wrench.

Firstly, the back wrench is an actual asset to my tool drawer.  The reason is because of its greater span than my regular wrench.  I felt this was important enough to make a short video to describe this.

The rest of the tool kit is a "mixed bag."

The screwdrivers are very similar to the classic Bergeon driver.  I illustrate a visual comparison as well as show the driver set that my Dad gave me for Christmas about 50 years ago.  The blades from the cheap kit are horrible "out of the box" so they must be dressed before use. 

The tweezer is very basic and just borders on usability.  I don't know the correct term for the "squeezability" of a tweezer, but compared to my Dumonts, the squeezability is pretty bad.  I had no expectation here, so am not really disappointed.  I will pack a Dumont tweezer (I have many) with the kit for better performance when necessary.

The bracelet pin remover stuff is OK at best.  I have one I had purchased separately and the quality of the metal is poor--bends easily.  The springbar remover tool is horrible--I show pictures of the end.  Not sure it will even work.  In TheLittleWatch shop, I use a "non-precision" screwdriver for removing spring bars.

The watch case holder is actually pretty nice.  I will find use for that...even here on the bench.

The bracelet holder is a nice idea.  I do not have one and I think it is useful enough to get one for the bench.

There are two "snap-back" removers.  Not sure why...perhaps to accommodate prying angle.  At this point, I have no opinion about them...until I try them out.

The kit comes with a little hammer that is kinda cute.  It is used for pounding in bracelet pins.  Has a metal and plastic head.

At then end of the day...it is worth the $20 I spent if only for the back wrench, movement holder, and bracelet holder.  The drivers are usable and the folding case is a compact way to carry a small number of tools.  As I actually use this kit, I plan to report back.

IMG_7508.JPG

2021-10-28 07_25_34-Window.png

IMG_7510.JPG

2021-10-28 07_27_13-Window.png

2021-10-28 07_27_36-Window.png

2021-10-28 07_27_55-Window.png

2021-10-28 07_28_10-Window.png

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
1 hour ago, LittleWatchShop said:

Firstly, the back wrench is an actual asset to my tool drawer.

My experience. Cheap wrenches do mostly work, but loose pins (years ago I used silicon grease to keep them in place), and the wobbly handle screw are unpleasant to use.

 

1 hour ago, LittleWatchShop said:

The screwdrivers are very similar to the classic Bergeon driver.

Minus the roller bearing probably, I don't know if "classic Bergeon" have that.

 

1 hour ago, LittleWatchShop said:

The blades from the cheap kit are horrible "out of the box" so they must be dressed before use. 

I'd rather buy 3 sizes of the "unbranded A*F" drivers.  Even my set of Chinese drivers is better than that.

 

1 hour ago, LittleWatchShop said:

The bracelet pin remover stuff is OK at best.  I have one I had purchased separately and the quality of the metal is poor--bends easily. 

I bought various cheap ones for gifting, and kept the less horrible. It still plastic, but has few spare tips inside and it works.

 

1 hour ago, LittleWatchShop said:

The springbar remover tool is horrible--I show pictures of the end.

You can buy Bergeon original (wow) screw-on tips for it. 

 

1 hour ago, LittleWatchShop said:

The watch case holder is actually pretty nice.

Yes it's of the sturdy breed. There is another type like that, uglier but even sturdier.

 

1 hour ago, LittleWatchShop said:

There are two "snap-back" removers.  Not sure why...perhaps to accommodate prying angle.

These are copies of Seiko which makes four types. What for each type is meant exactly is a Japan's trade secret.

 

1 hour ago, LittleWatchShop said:

 the folding case is a compact way to carry a small number of tools. 

We all like these cases as we had them since primary school except they were shaped like Mikey's head and the like. My other memory about that early "kit experience" is that the eraser was either rock hard and ripped the sheet right away, or smelled like sweets - probably harmfuls chemicals.
Not having anything less intelligent to add here, I wish you fun using it and leave a link which may be appropriate sometime

 

 

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Jon
      Part swapper to part maker

      By Jon · Posted

      I would use some binding wire around the part before heating it. It protects the steel from being burned. I know that sounds strange, as you're going to heat it with a blowtorch, but if a part is thin and delicate the steel can literally burn away before your eyes, which isn't funny if you've put hours into the job. I bought some tools steel from Cousins a few years ago which turned out not to be tool steel, because it couldn't be hardened or tempered. I wasn't impressed, as I had spent two hours making the part for it to be useless.
    • watchweasol
      Questions about my Bravingtons Renown Mantel Clock

      By watchweasol · Posted

      Hi that’s what was meant by animal glue “ a glue made from animal products”. Ie bone , skin and other animal residues.  There was a place at Huntington YORK who used to boil down the ingredients. It stunk.   We used it in pellet form in a sort of Bain Marie on a gas ring  it was very good, didn’t think it was around any more with the modern glues, 
    • Zedster
      Balance cock stud screw

      By Zedster · Posted

      It's back to the drawing board I'm afraid. As pointed out, the Rodico trick is so fiddly and my pin vice jaws don't close in union. I tried but the screw is so small it's hard to grip the screw in the Rodico without it moving all over the place while trying to get it in the vice. I started to shake too much so gave up before the screw flew off somewhere never to be found again.  I'm now thinking that maybe I could bond the screw on the end of a bit of peg wood and then dissolve the adhesive afterward.  I just had another thought🤔 I have some really small PCB drill bits maybe I could drill a small hole in peg wood and push the screw in, as stated I only need to get the screw started.  Another idea 🤣 Magnetize the screwdriver to hold the screw 🤔 
    • Chief
      Generic screws for unknown movements

      By Chief · Posted

      Yeah there is a spring under there. Hopefully now I can source a screw for the click and the bridges! Thanks for your help!
    • rjenkinsgb
      Identifying watch for possible radioactive concern

      By rjenkinsgb · Posted

      Definitely worthwhile, if you are working with old watches - just be sure it's an actual Geiger counter, not one of the vast range of scam/fake "Radiation detectors" on ebay & amazon etc. that detect RF or static electricity...   In the mean time, I'd put the dial and hands in zip bags & wipe down the work area with a damp cloth to pick up any dust, then discard the cloth. The emitted radiation from radium lume is not normally harmful - but inhaling or ingesting a single particle of the material can cause serious long term harm, so do take care with it.  
×
×
  • Create New...