Jump to content

Fractured Barrel

clockboy

By clockboy
in All Things Clocks

 Share

Recommended Posts

clockboy Distinguished Member

clockboy

Posted
Posted

I have finally found time to strip down the Fusee wall clock and despite its age it is still in pretty good condition apart from the mainspring barrel. It has a hairline fracture and I know the best option would be to make a new barrel but I only have a watchmakers lathe. Maybe perhaps to insert a sleeve but I guess that could cause issues when the spring unwinds. Normally I remove the mainspring etc and inspect and replace if necessary but not sure  by disturbing  the barrel it could cause it to fracture more. 
Any thoughts guys. 
 

61114FDF-9A15-40CF-B133-DD98E16F07E1.thumb.jpeg.524d216978dd2c847f932df02647d740.jpeg

Link to comment
Share on other sites
Rodgo Member

Rodgo

Posted
Posted

Hi wonderful the fusee clock.   Is it an Elliott?   Personally to strengthen from the inside of the barrel is the place to start.. but it is showing its age.. being a fusee they have been made with least wear involved.. I would put a sleeve in if you have the tools and workshop.. obviously the weakest spot..

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

Sorry to say the only way is to have a new barrel made. Get yourself a Unimat 3 then you can make one yourself. Trying to strengthen from the inside you will cut down the depth that the spring hooks on. If you just cover over the split the spring will rub against it and it will cause wear in the spring.  

 

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
  • Author
Posted
Just now, oldhippy said:

Sorry to say the only way is to have a new barrel made. Get yourself a Unimat 3 then you can make one yourself. Trying to strengthen from the inside you will cut down the depth that the spring hooks on. If you just cover over the split the spring will rub against it and it will cause wear in the spring.  

 

That’s my conclusion as well. All I can do for now is inform the customer and if it runs with the fracture then so be it. I desperately need a descent lathe but before that I need to clear my garage with is a big time consuming job. 

Link to comment
Share on other sites
Rodgo Member

Rodgo

Posted
Posted

The fracture is the beginning of the end of power for the movement. It will probably give another year or so of service .  I usually tell my clients if you wish it replaced , work your measurements and drawings. I can do it in my work lot ... otherwise don't wind it to its full.. A new Barrell  rather than a repair is the right way to do it..    all the best...if you don't have the right equipment think outside the box, it's amazing How necessity is the mother of invention...

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
  • Author
Posted
5 hours ago, Rodgo said:

The fracture is the beginning of the end of power for the movement. It will probably give another year or so of service .  I usually tell my clients if you wish it replaced , work your measurements and drawings. I can do it in my work lot ... otherwise don't wind it to its full.. A new Barrell  rather than a repair is the right way to do it..    all the best...if you don't have the right equipment think outside the box, it's amazing How necessity is the mother of invention...

Thanks Rodgo. That is what I have told the customer today. He is very happy as he was told it was not possible to get the movement running. He also is not prepared to pay for the cost of a new barrel. I have done my bit and on to next job.

 vid of it running on test before I polished and smartened it up.

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      That's the right technique Mal 👍 If you are ok with a loupe ( which I'm not ) then pick up the dial in your left hand and make a tripod holder out of 3 fingers and then exactly how Mal and me described with your right hand, press and flick out the stem at the same time. You need three fingers to do this, i use my ring ring finger , sounds like mal uses his little finger, just whatever you feel comfortable with. The key point and dangerous side to this is the tweezers or driver slipping off the release screw. Stablise your left arm by resting your elbow on your bench, so that you can hold the movement horizontally flat, use a x5 loupe to view  and good light so you can see well and have a good tight fitting screwdriver to push the release down. Or as suggested a pusher mounted solid upside-down somewhere then all you need to do is push your movement up to it. I'll rig something up in a bit to show you what i mean.
    • Neverenoughwatches
      Leaving the forum for a while.

      By Neverenoughwatches · Posted

      Thanks Michael, shes a real soldier, it would take a tank to knock her off her feet.  Shes surprised even me and i knew she was a tough cookie.  Good for you Michael, you keep at it. I've been reading your posts re. your watchroom they're inspiring and it doesn't matter how long it takes you to get there its about the journey. Rome wasn't built in a day, our watchcaves are our solitudes, our own little empires where we can shut ourselves away from the crap that goes on around us in the world. I look forward to seeing you progress, I have my own ideas how i like to do things. But in answer to your questions on that thread, just let your workspace evolve around you and how you work. You wont figure it out straight away but you will know when to change it and when to leave it alone. But most of all just enjoy it.
    • Malocchio
      Stem removal after fitting hands

      By Malocchio · Posted

      That can be tricky. Sometimes I hold the movement from the edges in left hand and with right hand I push the release with tweezers and simultaneously pull the stem out with right hand pinky or something. 
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      I see what you mean. I must admit I’m not entirely comfortable with that but I can’t see a better method than what you suggest. I’d like to see something like this mirror with a short spike: https://www.cousinsuk.com/product/mirror-for-observing-movements Place it on, push the spike on the post with one hand and release the stem with the other hand. Minor problem, it doesn’t exist.
    • Michael1962
      Leaving the forum for a while.

      By Michael1962 · Posted

      Hope you mum keeps on mending. I was adamant that I was going to get myself going after my stroke. I was only 52. I still have a lot of life left to live. Some people give up. Some people don't let it beat them. Your mum sounds like one of the winners. 👍
×
×
  • Create New...