Jump to content

"Knot" in a balance spring

Adrien

By Adrien
in Watch Repairs Help & Advice

 Share

Recommended Posts

Adrien New Member

Adrien

Posted
Posted

Hi!

I currently struggle with an ETA 1301 from a Eska watch, during cleaning of the balance wheel, the stud came into the third ring of the spring and made some kind of knot...

I do not want to break it but I don't know how I can extend the spring without breaking it to step backward from this situation.ETA1301_balancier.thumb.png.81aabd2828ad32efa97630623ad6da0c.png

Thank you for your help if you could tell me how to manipulate this spring without any risk of breaking!

Link to comment
Share on other sites
Graziano WRT Addict

Graziano

Posted
Posted (edited)

Hi there Adrien , firstly you would need to demagnetize it .I don't know  what tools or experience you have but you can use demagnetized needles or 2mm sharpened pegwood and gently work the hairspring not applying any sort of pressure  .try and chase the crossed over sections by spreading and chase to the stud end where it  free so you can maneuver the stud back through the spring . This will take some time, you do not want any manipulation that puts pressure on any part of the hair spring as this will bend it which is what you don't want .You can put the balance pivot into some pithwood to hold it while you work on it .Use a 10x loupe, If it has become distorted or kinked or doesn't lie true or center correctly then it is a different kettle of fish and correcting with the tweezers is a skill which can only be learned through practice. Anyway good luck and I hope this helps

Edited by Graziano
Link to comment
Share on other sites
Nucejoe Distinguished Member

Nucejoe

Posted
Posted

Stud always causes problems when untangling H/S, so I detach the stud off of balance first, this improves your chances of success greately, more so if you remove the coil (  from the balance ) and put the coil on a white sheet of paper spread on top of a hard flat surface.

Use a needle to chase ( from coil center outward ) , maneuver crossed circle with ease.

There have been couple of cases on this forum who didn't remove the stud and failed.

Regs

Joe

 

Link to comment
Share on other sites
Adrien New Member

Adrien

Posted
  • Author
Posted

Ok, thank you for your advices. I am not so comfortable with removing and replacing the stud, so I will try with much care as described by Graziano (thank you for the details).

If the "danger" is too high, I could then think of removing the stud if it seems to be too difficult (do you have advices for it, Joe?)

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Marc
      Seiko 6309a diver crown replacement

      By Marc · Posted

      Interesting interpretation of "traditional". I would say that Loctite is definitely the up-to-date and appropriate stuff to use, however, it is a relatively modern solution. Before the advent of such esoteric solutions I believe that the "traditional" thread locker of choice may well have been a sugar solution. Once applied the water would evaporate and the sugar would crystalise, locking the threads tight.
    • Marc
      Pocket watch winding stem sleeve

      By Marc · Posted

      @steve1811uk close but no cigar 🙂 I don't smoke anyway. I checked in my stock of parts and that's the closest I got to your dimensions. Good luck in your search. @RichardHarris123 I have an accumulation of all sorts of odds and ends that I acquired as a result of buying up the tail ends of old watchmakers estates. Usually after all of the great stuff has been stripped out, which means that the sweepings off of the workshop floor can be had for peanuts, but if you have the patience, can often be found to contain gold (both literally and figuratively 🙂 ). These came to me through on of those purchases. I doubt that I will personally be able to make use of even 10% of my accumulated stock, but having it, and knowing what I have, means that I can at least pass bits on to those who can use it whenever possible.
    • Curare
      Spell Check

      By Curare · Posted

      Hi and thank-you for your suggestions, as per Mark's instructions I checked my browser "Safari" and spell check and grammar was not ticked. So all sorted. Thanks CJ  
    • RichardHarris123
      Seiko 6309a diver crown replacement

      By RichardHarris123 · Posted

      As an alternative, clear nail Polish, the advantage is you can have a manicure at the same time. 
    • VWatchie
      Spell Check

      By VWatchie · Posted

      I use Grammarly. It works really well and If English is not your first language, you will also receive help with formulations. There is a free version that covers most of my needs. It installs as a plug-in and works with all browsers and word processors.
×
×
  • Create New...