Jump to content

1983 Timex Red Dot Diver - Before & After


JerseyMo

Recommended Posts

A recent online purchase and repair to a 1983 Timex commonly called "Red Dot Diver".  Bought in non-working order I found internal damage due to a sheared pillar screw. With the aid of my parts collection all was corrected.  Here is the before and after.

- New Crystal

- replace pillar screw

- replace hour wheel

- COA ( clean, oil, adjust )

- polish buff

Only follow up has been with the seconds hands not seating correctly.  This is very common with vintage Timex because there is no center tube. So once lifted off the seconds wheel the hole tends to be distorted.  Typically I will place hand on a flat metal surface and peen the metal down. In this case that did not work so I when to next level and add a dot of black nail polish. The watch would have originally come with a stainless steel bracelet and the white strap on it now is for wrist worn testing.

 

Before.jpg

After.jpg

  • Like 8
Link to comment
Share on other sites

  • 1 month later...

Great looking watch! I recently got this same watch in a lot sale. It's a strong runner, but the stem doesn't seem to seat inside the movement in a secure enough manner to wind it. It will slip when trying to wind. I'm fairly familiar with taking these apart but I haven't encountered a Timex like this yet where the movement is fastened inside the case. I can't quite figure out how to remove it from the case. I've snapped one of those 4 pins holding the dial on before so I've been skittish about playing with it too much. Really awesome to see your before-after photos. Thanks!

Link to comment
Share on other sites

23 hours ago, TC519 said:

the movement comes out the front.  Pop the case back off and remove the stem crown by loosening the set lever screw a little. Next lift the bezel ring and the crystal. Then movement will than come out the front.  It sounds like there may just be some built up grime in the stem tube.

 

 

Link to comment
Share on other sites

 

Wow. These must be a seasonal thing. Finished this one last week. Maybe they somehow appear most frequently during tax season. 

Timex2021-05-11-174900.thumb.jpg.66a2294c62b9b02ae92a4101bd2da993.jpg

 The proportions, and layout of this watch aesthetically, is IMHO is  so pretty, that at the risk of sounding snobby, I'm amazed Timex ever managed such a design. If it were a sterile dial, and I were guessing, Omega might seem a possible influence. The red dot, floating around the dial is the iceing on the cake. If only more of Timex's other watches of that period were this nice.

  • Like 2
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hi nickelsilver, thanks for the great explanation and the links! I'll take a good look in the article.  Especially this is great news to hear! Looking through forums and youtube videos I was informed to 'fist find a case and then fit a movement for it'. But seems that's not the case for pocket watches at least?  I guess I should be looking to find some 'male square bench keys' for now. I was thinking of winding the mainspring using a screwdriver directly, but I found a thread that you've replied on, saying that it could damage the spring. 
    • Murks, The rate and amplitude look OK, and the amplitude should improve once the oils you have used get a chance to move bed-in, also I notice that you are using default 52 degrees for the lift angle, if you get the real lift angle (assuming it's not actually 52) this will change your amplitude - maybe higher, maybe lower. I notice that the beat error is a little high, but not crazy high. At the risk of upsetting the purists, if the balance has an adjustment arm I would go ahead and try and get this <0.3 ms, but if it does not have an adjustable arm then I would probably leave well alone. Just my opinion.
    • Hi everyone on my timegrapher it showing this do a make anymore adjustment someone let me know ?    
    • Maybe I'm over simplifying this and I'm a little late to the discussion, but just by my looking at oil when I use it on a treated cap jewel  the oil stays in one nice bubble, but when I don't it spreads out to the edges of the jewel. I'm not sure (but could well be wrong) but the analogy of a waxed car and rain is accurate in this case, the wax is very hydrophobic and repels the water, however, the process epilame works by is a different physical process based upon cohesion/adhesion (oleophilic) not repulsion (oleophobic)  at least as far as I have read/observed. If one were to use a oleophobic substance equivalent to wax (hydrophobic) then one would need to create a donut shape to fence in the oil, however if one used such a strategy with a epilame which is oleophilic then the oil would sit on the ring of the donut and not in the 'donut hole', exactly where you don't want it. Even if the oil is smeared then the oleophilic epilame should pull it back to the center (see diagram below). Reference For interest the chemical in epilame is 2-(PERFLUOROHEXYL) ETHYL METHACRYLATE, CAS NO: 2144-53-8
    • Looks lint the teeth on the hour wheel aren't meshing with the teeth on the calendar intermediate wheel, maybe the hour wheel is sitting on top of this instead of meshing?        
×
×
  • Create New...