Jump to content

Best luminous watches


Recommended Posts

Found this interesting article about luminous watches:

Using  photoluminescent material to show the time in low-light conditions is a practice that has been employed since the development of the earliest wristwatches.

Originally, radium was used on hands and indexes, which had the benefit of a bright and long-lasting glow, counterbalanced by the disadvantage of being highly radioactive and a major health issue for those who applied it.

In the 1960s, radium was replaced by the much safer, yet still radioactive, tritium, which was phased out in the 1990s when alternatives like strontium aluminate (in the form of Super-LumiNova) came to market.

The idea behind practically all forms of ‘lume’, though, is that they absorb light during the day, store it and then emit it in the dark. The most common colours are blue, green and white, but this is by no means all that is available. Usually coating hands and indexes, the more adventurous manufacturers - like the ones listed below - have found ways to add light shows to dials, bezels, cases and even straps.

A good example is the following beauty.See pic

Price: £1,800 | Ball Watch Co.  

According to Ball watch, the self-powered micro tubes that have become its trademark are 100 times brighter than standard luminous coatings, and, although the glow will gradually fade over time, a replacement dial will easily solve the problem. The illumination is achieved through H3 tritium gas, safety-sealed in mineral glass tubes that are coated with a luminescent material. And nowhere is the light brighter than in the recent Engineer III Marvelight. With rainbows now a symbol associated with 2020 and the global fight against Covid-19, Ball has issued the limited-edition 40mm watch with multi-coloured gas tubes. For every piece sold, 300 Swiss Francs will be donated to The Salvation Army.

71D757AC-2D68-42B2-9C7D-139071569350.jpeg

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hell0 @nevenbekriev. Thank you for your advice. I have removed the old setting using my staking set--I will keep the KIF spring, since it is still good.  I am awaiting the replacement setting, and will update when I do that. In the mean time, I looked at the escape wheel and it looks ok. What do you think?    
    • Aloha All, I recently bought this Seitz tool on eBay, but it is missing some pushers reamers.  I ended up ordering new parts for those that were missing before I received the actual Seitz tool (bad idea).   Upon inspecting the pushers/bits, I noticed 23 of the 56 provided with the set had no numbers. Further inspection revealed a huge difference in the quality of those unnumbered.  Do all Seitz pushers/bits have a number on them?  I'm pretty sure that 33 of the 56 I received are cheap Chinese knockoffs.  The worst part is that I ordered $80 of parts to replace the missing pushers/bits, and now I'm looking to return the tool. I'm not crazy, right? If these are Seitz parts, they should all be numbered, correct? The first two pictures are the Seitz (numbered), and the other pictures are the suspect parts.  Will I even be able to get a refund?  Thanks, Frank     
    • It was £10 + min fee, total £16, could not leave it there. Its a Stanton A.D.2. http://stanton-instruments.co.uk/
    • Chief- The picture below shows the three parts from the dial side that are most useful to "fingerprint" a movement in conjunction with the diameter of the movement.  That's why forum participants are always asking for dial side photos in posts asking for identification.  As far as the setting lever screw, it actually sits loose in the main plate. The threads engage the setting lever below, and the elongated stem above the shoulder sticks through a hole in one of the bridge plates so that it's held captive if unscrewed all the way.  So you may be fine as far as that goes. 
    • So I found what I believe is the setting lever screw! Am I right in thinking the screw next to the click is the correct one for the setting lever? However if it is, it doesn't fit in the hole which I believe is for it! I can get the lever to sit nicely on the stem and line up with a hole, but the screw only goes as far as the shoulder and stops. It's as though the hole is too small! The dial side has been disassembled by the way, the other wheels are in my tray
×
×
  • Create New...