Jump to content

Lemania 3050


Marc

Recommended Posts

I'm wearing this little baby today. It ranks as one of my best bargains ever.

 

post-73-0-18660100-1390995424_thumb.jpg

 

Believe it or not it was a car boot score. A freezing Easter morning with only a handful of sellers and this antiques stall with mainly furniture and just a couple of odds and ends including this in a rather grubby and non-running state. The seller was deep in conversation with another trader, comparing takings and discussing a large mahogany chest of draws, and didn't seem too interested in my custom. when I asked him his price for the watch I almost fell over when he said £10. Recovering my composure and being the cheeky git that I am I decided to haggle and offered him £5. He wasn't interested but to my amazement he did meet me half way and the watch was in my pocket for £7.50 before he could change his mind.

 

Once home I opened it up to find this inside;

 

post-73-0-09335100-1390995434_thumb.jpg

 

Lemania Cal. 3050 17 jewel indirect center seconds with Glucydur balance and Breguet over coil hair spring. All that was required was a full service and re-lube, a new crystal, and a clean up of the all stainless steel case.

 

I'm guessing mid 50's based on styling and very loosely on the serial number. There is also a service mark in the case back dated Nov 61.

 

Enjoy.

Link to comment
Share on other sites

Another fine watch that will not be consigned to the dustbin of history,  well done Marc.  There must be shed loads of watches out there, forgotten about in cupboards and drawers that are well worth saving.  My biggest problem is getting hold of decent non running watches to work on,  I've seen the Ebay offers of a dozen for £XX's  most of which are just cheap junk and not worth bothering with,  where are the Vacheron & Constantin watches for a fiver?

 

RogerC

Link to comment
Share on other sites

Hah! - I wish as well... During the last 2-3 years I've noticed a steady increase in the price of halfway decent watches, and they're certainly not as easy to find as they used to be. I find the odd beauty from friends down the pub.

 

RogerC

where are the Vacheron & Constantin watches for a fiver?
Link to comment
Share on other sites

I haven't done too badly out of car boot sales but you do have to be patient and be prepared to do a lot of rummaging in boxes of junk. I also find some of the less well informed sales spiel that you get when someone senses that you're interested in an item extremely amusing, although that amount of "up selling" invariably means an unrealistic asking price.  

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hello, I am about 5 months into watchmaking and I love it!   The attention to precise detail is what really attracts me to it. (and the tools!) I am working on a 16 jewel 43mm pocket watch movement.   There are no markings besides a serial number (122248) .  The balance staff needs replacement. The roller side pivot broke off.  I successfully removed the hairspring using Bergeon 5430's.  I successfully removed the roller using Bergeon 2810.   Did i mention I love the tools?! I removed the staff from the balance wheel using a vintage K&D staff removal tool  with my Bergeon 15285 (that's the one that comes with a micrometer adjustment so it can be used as a jewel press as well as a traditional staking tool...it's sooooo cool...sorry..  can you tell i love the tools?) No more digressing..  I measured the damaged staff in all the relevant areas but I have to estimate on some because one of the pivots is missing. A = Full length  A= 4.80mm  (that's without the one pivot...if you assume that the missing pivot is the same length as the other pivot (I'm sure it's not)  then A = 5.12 mm...(can I assume 5.00mm here?) F=  Hair spring collet seat  F=  .89mm   (safe to assume .90 here? .. I am sure that my measurement's would at least contain  .01 mm error ?) G = balance wheel seat  G = 1.23 mm  (1.20mm?) H  =  roller staff  H =  .59mm  (.60 mm?) B  = bottom of the wheel to roller pivot   B  = 2.97mm  (3.00 mm?)     here I am estimating  again because this pivot is missing. So my friends, and I thank you profusely,  can you point me in the right direction as to how to proceed? Do i buy individual staffs?  or an assortment?   Since I don't know exactly the name of the manufacturer, will that be a fatal hindrance?   Tbh, I'm not even sure what country of origin this movement is. Thank you!    
    • Thats why i asked that question earlier, what happens if lubrication is placed directly on top of epilame ?  As opposed to walled within its non epilamed area . I'm not saying its right, i have no idea , just asking questions. 
    • thinking of where epilam should be removed did you know there was a patent that covers this? At least for the escapement I'm attaching it. GB1057607A-1 epilame.pdf
    • Back home...printing now.  Will report results
    • Oh well, if Master @nickelsilver says it's the way to go, then it is the way to go! I stand corrected! 🫡 Are there any other places where you're supposed to remove the epilame from the contact point of rubbing? I don't think so! Thanks for the effort @Neverenoughwatches, much appreciated! 🙂👍
×
×
  • Create New...