Jump to content

Baume et Mercier Hamilton Battery ?


Recommended Posts

Hi All - I own a Baume et Mercier Hamilton Quartz. It has not run in a while and I would like to replace the battery. It was purchased in the 1995 so there is no warranty. The only information I can find online is to send watch back to Baume et Mercier customer service. 

I am new to watch servicing world but I would think changing the battery of a quartz movement is not the same as servicing a Valjoux 7750. I could spend $45 and have it service by manufacturer but it would go against the reason why I joined this watch servicing community. 

Does anyone know what battery is needed and where I can purchase online ?

If there is a good reason why I should not change battery myself, I am open to discussion.

Thank you... AJ

 

Link to comment
Share on other sites

You might have to pop the back off, or otherwise open the case to get the battery. The movement is probably made by someone else, like ETA, for Baume. However, without the movement caliber number it'll be more of a guess, methinks.

Otherwise, if you can find the same model on the auction site, and the back is off to show prospective buyers, that might clue you in. Still not definite though. Good luck.

Link to comment
Share on other sites

On 6/7/2019 at 5:15 AM, ajdo said:

I will pop the hood of my Baume et Mercier Hamilton this coming weekend and see what I can find a reference number on battery. 

Even without a battery at all you can identify it by the mov.t, or by  the size of the slot using the table attached.

ScoSu_Consumer_renata.pdf

Link to comment
Share on other sites

I tried to open B&M Hampton (purchased in early 90s) case but was unsuccessful and do not want to scratch it.

I think it’s time to start investing in better tools! 

I used one of those red knife-like that comes in a basic watch tool set but was unable to open the back of B&M Hamilton :( Tried the same tool on another inexpensive quartz watch I own and had the same issue, the “knife” just slipped off. 

I think I need some type of lever type tools which I suppose would make it easier. It could also be that I do not have the proper technic. 

If someone can shime-in on the proper tool I should get that would be great.

I guess it’s the biginning of a tools buying spree :) I will not work on my nice watches but my new found goal is to take appart, lube and put back together a Seagull 2824 I found in a clone Rolex I have. 

A tool list would be welcome. I am more middle of the road person, I do not like cheap tools but would not spend big $$$ on an activity I do not know will actually become a hobby. It’s really out of intereest for now but do not want to end up like Charlie Chaplin in Clock Repair short movie :)) 

Edited by ajdo
Watch model mistake
Link to comment
Share on other sites

52 minutes ago, ajdo said:

 

I used one of those red knife-like that comes in a basic watch tool set but was unable to open the back of B&M Hamilton :( Tried the same tool on another inexpensive quartz watch I own and had the same issue, the “knife” just slipped off. 

As often asked, tight snap on case backs are opened by first going around slowly and carefully with a blade like an exacto knife. After is lifted enough theb use a case back knife, Japanese types are good, pry around don't twist it. 

These subjects are well covered in the forum, just browse around. 

Link to comment
Share on other sites

Since you mentioned better tools.

https://www.aliexpress.com/item/New-Watch-repair-tool-Heavy-Metal-Made-Adjustable-Watch-Case-Snap-Back-Opener-professional-removal/32344173972.htm

With tips for bracelets, $10 more
https://www.aliexpress.com/item/New-Watch-repair-tool-Heavy-Metal-Made-Adjustable-Watch-Case-Snap-Back-Opener-professional-removal/32344173972.html

You also need a small press to close the back. But unless you do a lot of snap back, they are totally an overkill. Much more needed is good screw-in opener.

 

  • Like 1
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Just missed it! I have a donor movement on its way. But thank you for the offer--I'll let you know if I need anything else.
    • My latest. Timex 2465. Replaced the crystal, caseback gasket and spring bars. All in less than $5US. Added a gray NATO strap I already had in stock.
    • I have some Gruen 510's in my donor pile if you need parts.
    • I've been intrigued by everyone's input here...so I decided to give this a shot. I bought the"typical" Pearl watch-machine basket and trays, for about $65. The trays are good,..the housing is a nightmare ! Thought it would take the mixer off my bench at anything above about 200rpm. The housing is cast of course,..and it's not "true" at all...so the harmonic vibration was insane. So,..I bit the bullet and bought the Elma housing and top. Not the baskets though, as the Pearl one's fit the Elma. Saved a bunch there. The basket and lid came to about $80 with shipping. The opening in the Elma top is 8mm, and the shaft that came with my stirrer is 6mm. I bought a piece of steel tube, 8mm O.D., and 6mm I.D. Cut off about an inch of the tube, and drove the rod into it. Gives a really snug fit.... Lightly champfered the leading edge of the 8mm section, then lightly tapped it into the top of the Elma lid. Spins like a dream now So... I have about $240 total into this including jars and steel mesh for the wave breakers   I'm pretty happy Best to you all   Randy
    • Still haven't gotten around to getting stems or screws, but I did make my first attempt at polishing a case. I just used a soft mop and rouge to reduce my odds of ruining them, and I think they came up pretty nice. Also gave the crystals a polish on the same wheel while I was at it. They were both very badly scratched up. The one on the left is fairly beat up, but it'll still make for a decent presentation.
×
×
  • Create New...