Jump to content

Recommended Posts

Posted (edited)

Hi everyone, I realise that this is a purists forum but I fix all sorts of watches so I ask a question. 99% of the time I use Silver Oxide batteries for quartz watches, however I have noticed that when left for a long period flat, the battery may leak and rot and corrode the -ve terminal. Sometimes needing quite a repair. These batteries contain an alkaline electrolyte but due to the Sil Ox give a flatter voltage output they say. I have just performed a very basic test as follows on a new alkaline battery... Off load voltage 1.552 V,   Max current 2860 microamperes. About the same as the equivalent Sil Ox battery. I have not performed an extended test. Any constructive comments would be welcomed.

Edited by ecodec
correction
Posted

This article has a lot of good information on this topic, including types and brands they found were less likely to leak: http://www.great-british-watch.co.uk/how-to-spot-and-deal-with-watch-battery-leaks/

I've just decided that whatever the benefits of silver oxide are, they are outweighed by the risk of using them, so I use lithium whenever I can. Whenever I can't, I replace them every three years or so, dead or not, and recommend that anyone I replace them for do the same. 

Posted

One of the unfortunate problems of electric watches are the power source. Ever since they made the first electric timepiece the chemical battery is a problem. So for the most part sooner or later the batteries will all leak if you give them enough time.

3 hours ago, qhartman said:

I've just decided that whatever the benefits of silver oxide are, they are outweighed by the risk of using them, so I use lithium whenever I can. Whenever I can't, I replace them every three years or so, dead or not, and recommend that anyone I replace them for do the same

So I'm curious lithium batteries typically are physically sized differently then silver cells how do you deal with that? Then there is the other problem the voltage difference 1.55 versus 3 V?

 

 

Posted
7 hours ago, qhartman said:

This article has a lot of good information on this topic, including types and brands they found were less likely to leak: http://www.great-british-watch.co.uk/how-to-spot-and-deal-with-watch-battery-leaks/

I've just decided that whatever the benefits of silver oxide are, they are outweighed by the risk of using them, so I use lithium whenever I can. Whenever I can't, I replace them every three years or so, dead or not, and recommend that anyone I replace them for do the same. 

Thank you qhartmann for your help, Mike. ECODEC.

Posted




So I'm curious lithium batteries typically are physically sized differently then silver cells how do you deal with that? Then there is the other problem the voltage difference 1.55 versus 3 V?
 
 


Doh. I was thinking of alkaline vs silver oxide when I dashed that off. It would be nice if lithium were an option, but as far as I know unless the watch is designed for it, it isn't for the reasons you state. Sorry my haste let some misinformation get out.

Sent from my ONEPLUS A5000 using Tapatalk

Posted (edited)
10 hours ago, qhartman said:

This article has a lot of good information on this topic, including types and brands they found were less likely to leak: http://www.great-british-watch.co.uk/how-to-spot-and-deal-with-watch-battery-leaks/

I've just decided that whatever the benefits of silver oxide are, they are outweighed by the risk of using them, so I use lithium whenever I can. Whenever I can't, I replace them every three years or so, dead or not, and recommend that anyone I replace them for do the same. 

Thank you Sir. Ecodec.

 

Edited by ecodec
more info
Posted

Not all batteries are created equally, theses are 1961 W-1 batteries.

eKObIJhFNh1TjaNiyRmB1OBM95DXF30NsbVurWy6

not bad for 57 year old cell batteries

but yes, I never leave a cell in after I let the watch cool off after wearing it.

  • Like 1
Posted

Hi Guys   I think the moral of this story is never store quartz  watches or clocks with batteries in as all batteries given time will leak causing damage, best to remove the battery and fit a label as to what type it takes then its easy to pop one in when you want to wear it. saves scratching the head trying to remember what was fitted.

  • Like 1


  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Thanks for that Andy, Yes the new bracelet is worth more than the watch itself, Its one I have bought to service and clean-up and on-sell it as a project, look it may sell to someone who has a small wrist, I think I will buy an extender and may-be offer it up with a normal strap as well CJ
    • Not always that simple. Typically the only reason we would have any way of identifying a watch is if parts were available at any time and somebody had a parts reference book then they would help you to identify the watches that they have parts or. Unfortunately there are hundreds of thousands of watch movements with no identification and of course typically no parts the classic place were watches would be identified would be under the balance wheel and your pictures don't really show a good view of that. Occasionally I've seen watches marked under one of the plates. They felt very proud of their watch is a very prominent Swiss company and they ask he stamped the bottom of a plate so you have disassembled find it. Then there is the other system the keyless parts make up something called the fingerprint system but you still haven't given us enough information to make use of that. Here's an image showing what a fingerprint system looks like. The PDF is based on the physical book the physical book has sizes of watches these are smaller ladies watches and keyless parts which in the physical book are printed at the actual size of the watch parts. So to identify with the keyless we need in your case diameter measured on the dial side and a good picture of the keyless parts and then you have to hope that this was made within the right time span of the books that have this system on the other hand a lot of times on the dial side they will also put markings. So basically to identify a movement it has to come out of the case and has to be disassembled.
    • The strap is a 44Q6JB and hadn't realised how much they'd gone up in price. The used one I've got is very worn but may have other links floating around.
    • @Mercurial is this also a variation of the tool you posted? 
    • Thanks Andy, The bracelet is sized very small, around a 14cm wrist. Were would one try to source original links, I guess they wouldn't be cheap if found. The bracelet end links have 4406 B-E stamped on them, is this the Seiko Bracelet code ?? CJ  
×
×
  • Create New...