Jump to content

looking for source - ebel model 1157111 gasket

PWR

By PWR
in Watch Repairs Help & Advice

 Share

Recommended Posts

PWR Member

PWR

Posted
Posted

I am replacing battery on my wife's lovely Ebel ladies wave and the gasket on the bezel is shot.

Model # 1157111

My Dad was the Ebel service agency in Phila but he is gone and I'm stuck looking for a new gasket.

Ideas on source for gasket or even part number?

 

thx

 

Steve

Link to comment
Share on other sites
wls1971 Distinguished Member

wls1971

Posted
Posted

Ebel parts are very difficult to get why must it be Ebel ? Its just a round gasket that fits in a groove at the back of the bezel its not a fancy shaped gasket so it should be possible to fit a generic Swiss gasket.

Link to comment
Share on other sites
Tudor Distinguished Member

Tudor

Posted
Posted

Measure the o-ring groove ID and the o-ring cross section and then visit www.mcmaster.com and search for O-rings.

Note they have Metric which are easy and the US (Parker) standard numbering system for the "inch" ones. Get your measurement converted inches and mm and search both (exactly 25.4mm per inch conversion).

Another thing is that the smallest cross section is 1mm, so if it's a thin 0.5mm o-ring you have to search/ask the watch supply houses, which will cost more.

Link to comment
Share on other sites
PWR Member

PWR

Posted
  • Author
Posted

thanks all...I guess I am a bit of a snob as I was trained to use genuine parts whenever possible.   But you are all right and a generic gasket will work well.   I have ordered a set of various sizes hoping one will fit.

Link to comment
Share on other sites
PWR Member

PWR

Posted
  • Author
Posted
On 9/11/2018 at 2:38 PM, Tudor said:

Measure the o-ring groove ID and the o-ring cross section and then visit www.mcmaster.com and search for O-rings.

Note they have Metric which are easy and the US (Parker) standard numbering system for the "inch" ones. Get your measurement converted inches and mm and search both (exactly 25.4mm per inch conversion).

Another thing is that the smallest cross section is 1mm, so if it's a thin 0.5mm o-ring you have to search/ask the watch supply houses, which will cost more.

so when I go to referenced website, there are a zillion choices for material of O ring....can you be more specific?

Link to comment
Share on other sites
vinn3 Distinguished Member

vinn3

Posted
Posted

there books and books on o rings,  both metric and inch.   the o ring groves diffrer depending on its use.  the material differs also depends on use.  temperture,  solubility,  age of material formula, etc..   i don't know of any designed for watched.   they worked great on radial engines.   vin

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • AlanB
      Gilding after silver soldering

      By AlanB · Posted

      When faced with say a pocket watch bridge which is cracked, silver soldering to repair is often the only option (hopefully someone wasn't there before hand with soft solder). I can generally do this succesfully and tidily with a small torch and miniscule pieces of silver solder, but on parts which were mercury amalgam gilded the heat can have have a deleterious effect on the finish.   I keep wondering if there's a good way to refinish these - and despite having the needful items would rather avoid using the mercury process.   In the past for electronic work I've gold plated PCBs but this involved gold potassium cyanide solution, which also doesn't realy belong at home. I've read that there are now safer alternatives but couldn't find more detail (and importantly how similar are the results to amalgam gilding, since I wouldn't want to refinish the whole watch). Pointers would be very welcome (and yes, I know solutions containing gold won't be cheap!) Alan
    • Neverenoughwatches
      Can anyone identify what this is? Part Two

      By Neverenoughwatches · Posted

      The first one is an Unruh max stake for pushing out staffs
    • JonC
      Can anyone identify what this is? Part Two

      By JonC · Posted

      Ok so with the great answers for my previous question may I ask what these two attachments are used for. The one with the red knob is I assume used for hand setting the seconds hand? Jon      
    • Zedster
      Roamer Searock Crystal problem

      By Zedster · Posted

      According to Cousins site I need to look at document G22 as I think I need an ATGB at 304 but I cant find this size in G22 doc. The last thing I want to do is order the wrong one😳  Unless I cant see the wood for the trees 😆 I could be looking at the wrong style, I assume its classed as Round plastic Armed  https://www.cousinsuk.com/product/wide-ring-gold-atgb
    • JonC
      Dial feet removal

      By JonC · Posted

      When building a new Watch I have tended to use a file to remove the remnants of dial feet that are not needed as many dials come with four feet to accomodate different movements, but this can be a bit messy so now I use this with a great deal more precision as you can use an appropriate bit for the job and keep it very localised.      
×
×
  • Create New...