Jump to content

Anchor Branded Crystal Lift Tool


Recommended Posts

Hello All,

I have been buying some bits and pieces to get me going and have come across this: Anchor branded crystal lift tool.  I know its not the same quality as Burgeon but will it do the job.  As you are aware I am totally new to this and would appreciate any advice.

Regards

Col

Link to comment
Share on other sites

Hi colored,

 

I have come across some anchor products and the quality in mostly shaky at best. I believe you might hopefully make this product work most of the time. I personally use the Bergeon one which in most cases is trouble free...but more expensive.

 

And welcome aboard!

Link to comment
Share on other sites

Yes, my 955i Triumph Daytona, no fuel getting to the injectors. I've not given up yet though.

Triumph! good man. Had a Speed Four a few years ago, now have an 2003 Trophy 1200. I did have a couple of injectors go south on the Speed Four, I wouldn't expect all 3 to go but you never know, If not its probably the pump, possibly wiring. Again the Speed Four had an intermittent problem with the engine cut out, eventually traced to a bad factory join in the middle of the main loom.

  • Like 1
Link to comment
Share on other sites

That could be easily fixed with the anchor crystal tool I think! :) Just use it to extract the loom! (As if I knew what you guys are talking about....woooosh, over my head!) :)

All very similar though, I initially took up watchfixing (I fix them, I don't make them) as a substitute for fixing motorbikes, all very similar just an awful lot smaller. Plus the added bonus of a nice warm room in the winter instead of a very cold garage.

Link to comment
Share on other sites

I agree totaly Blacklab, it seems like a good choice for winter time! I'll get a warm room anytime for a workshop! I've never been good at motorbikes although I used to dabble more with cars...that was soooo long ago it seems like another life! But I loved it therefore watches.

 

@Geo: I bet it won't be long now you'll be riding that bike again! keep us posted!

Link to comment
Share on other sites

Nice bike Geo.  I had the 955i RS sprint with the same engine and loved it.  However I had to get rid before it got rid of me. A pal had the speed triple with the same fault i.e. no fuel and it turned out to be a wiring loom fault.  I am looking for something a bit more docile now, age is getting the better of me.

Thanks for your advice re crystal lift

Col

Link to comment
Share on other sites

All very similar though, I initially took up watchfixing (I fix them, I don't make them) as a substitute for fixing motorbikes, all very similar just an awful lot smaller. Plus the added bonus of a nice warm room in the winter instead of a very cold garage.

 

A few days ago I took apart a door handle that was squeaking. Watchfixing skills came in handy... :)

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • To be honest, they're not a good movement to have in a chronograph for several reasons. The first is the chronograph mechanism is a 'bolt on' module; If you look at the side of the watch case the crown won't be in line with the pushers, therefore only the branded company would have the ability to swap out the module because they aren't designed to be serviced and definitely not by an independent watchmaker. Secondly, the ETA 2892 A2 is a great movement, but when the chrono module is used with it it becomes pants, in my opinion/experience. So, going back to your watch. The problem isn't with the base movement, which is the 2892A2, as there would never be that amount of backlash/flutter in the gear train of that particular movement, it is with the chrono bolt on module that the problem lies and when the chrono sweep second hand is engaged the flutter of the second hand is remedied by the stability of the chronograph mechanism negating that flutter. Everything in the chronograph mechanism of that movement is powered by a wheel in the centre where the cannon pinion/driving wheel would normally be. I think it is a crappy design deliberately engineered to be disposable due to the time taken to service the module. Give me a 7750 any day!
    • Yeah not much going on in the town , Scarborough is a bit better,but the missus and me love York. Good antique shops there, The antiques center on stonegate has a good selection of vintage watches, top price though.
    • Thank you for your introduction and welcome to this friendly forum. We all look forward to your contributions and continued involvement. 
    • Brid isn't what it used to be, I only really go to Morrisons in brid. I avoid the town. But Scarborough is nice! I don't mind a wander round the beach between jobs
    • I have had a few issues with my Orient Automatic crystal and bezel. The bezel came off with a case knife and I haven't been able to refit it. Doing a bit of research on here, I think that it is an arrangement where the crystal is snapped over a lip on the caseback and then the bezel is installed over the top like a tension ring. I have managed to crack the crystal trying various attempts to press it onto the case. Measuring the crystal with Vernier calipers, I think it is a Sternkreuz XS 314.171 but I can't correspond that to the reference/ case number on the caseback. I also measured the outer diameter of the lip on the case that it may fit over and this is 30.5mm, which is actually 0.7mm bigger than the static inner diameter. Is it likely that the crystal can be expanded enough to snap over that? The inner diameter of the bezel/ tension ring is 32.2mm which works with 31.4+0.7 = 32.1mm Does this sound correct? What method should I use to snap the crystal and then bezel into place? I have a cheap case back press with nylon dies but I managed to break the old one with this method.       
×
×
  • Create New...