Jump to content

What type of screw is this?

Lawren5

By Lawren5
in Watch Repairs Help & Advice

 Share

Recommended Posts

Lawren5 WRT Addict

Lawren5

Posted
Posted

I'm working on a vintage Citizen watch and came across these screws that are used on the barrel, ratchet and crown wheel. They each have three slots in them but don't seem to take a screwdriver.
What type of screw is this and what is the correct method for removing them?

citizen_screw_heads.JPG

citizen_crown_gear.jpg

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted

That is a left hand thread screw. A normal screwdriver should work . Had one on the barrel on the citizen 1803 i serviced recently. Which makes it hard to remove as the barrel wind when you remove it . I hold a finger on the ratchet wheel. 

.. 

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted

I don't know and don't quite understand the power flow of this, is it an alarm mov.t?

I can't understand neither why a left threaded screw would be used on a wheel turning clockwise. Of the two meshing above, one certainly is.

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted
10 minutes ago, jdm said:

I don't know and don't quite understand the power flow of this, is it an alarm mov.t?

I can't understand neither why a left threaded screw would be used on a wheel turning clockwise. Of the two meshing above, one certainly is.

Not sure why citizen has done this. But sure is left hand threads on all of this screws. It's an alarm movement. 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Mercurial
      AS2063 - hand setting

      By Mercurial · Posted

      Have you got the pallet fork installed in the movement when you see the train move when using the setting works? As nevenbekriev said, without the pallet fork to lock the train, the behaviour you are describing is normal. If this is happening with the pallet fork installed, you have a problem in the gear train, it should be immobile when the pallet fork is locking the escape wheel.  The fit of the circlip above the pinions on that wheel is crooked in your pictures, it should sit flat up against the upper pinion as in Marc’s picture.  Hope that helps, Mark
    • Khan
      Stem broken - can it be rescued?

      By Khan · Posted

      Hi I got a Jaeger LeCoultre K911 movement, where one of the stems was broken. Part no. Should be 401.  Im based in Europe and tried Cousins but its discontinued. They except to get stem in stock for cal. K916 but will that work? Or Is there a way out to join the ends?
    • Bonefixer
      AS2063 - hand setting

      By Bonefixer · Posted

      The part was how it fell out of the movement - the train wheel bridge wasn’t screwed in.    I’ll probably dismantle the part, if I can, to work it out.    The train of wheels ran fine - it was only once the keyless works were installed I noticed the problem. 
    • mthomas828
      Balance staff sourcing?

      By mthomas828 · Posted

      Hello, I am about 5 months into watchmaking and I love it!   The attention to precise detail is what really attracts me to it. (and the tools!) I am working on a 16 jewel 43mm pocket watch movement.   There are no markings besides a serial number (122248) .  The balance staff needs replacement. The roller side pivot broke off.  I successfully removed the hairspring using Bergeon 5430's.  I successfully removed the roller using Bergeon 2810.   Did i mention I love the tools?! I removed the staff from the balance wheel using a vintage K&D staff removal tool  with my Bergeon 15285 (that's the one that comes with a micrometer adjustment so it can be used as a jewel press as well as a traditional staking tool...it's sooooo cool...sorry..  can you tell i love the tools?) No more digressing..  I measured the damaged staff in all the relevant areas but I have to estimate on some because one of the pivots is missing. A = Full length  A= 4.80mm  (that's without the one pivot...if you assume that the missing pivot is the same length as the other pivot (I'm sure it's not)  then A = 5.12 mm...(can I assume 5.00mm here?) F=  Hair spring collet seat  F=  .89mm   (safe to assume .90 here? .. I am sure that my measurement's would at least contain  .01 mm error ?) G = balance wheel seat  G = 1.23 mm  (1.20mm?) H  =  roller staff  H =  .59mm  (.60 mm?) B  = bottom of the wheel to roller pivot   B  = 2.97mm  (3.00 mm?)     here I am estimating  again because this pivot is missing. So my friends, and I thank you profusely,  can you point me in the right direction as to how to proceed? Do i buy individual staffs?  or an assortment?   Since I don't know exactly the name of the manufacturer, will that be a fatal hindrance?   Tbh, I'm not even sure what country of origin this movement is. Thank you!    
    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      Thats why i asked that question earlier, what happens if lubrication is placed directly on top of epilame ?  As opposed to walled within its non epilamed area . I'm not saying its right, i have no idea , just asking questions. 
×
×
  • Create New...