Jump to content

Another Smiths

mwilkes

By mwilkes
in Your Watch Collection

 Share

Recommended Posts

mwilkes WRT Addict

mwilkes

Posted
Posted

Found this sad artefact on the bay. Once again the setting spring had broken. It now runs, but damned if I can get a decent amplitude - 180 degrees is the best I can squeeze out of it.

Before:

post-148-0-59468500-1411506739_thumb.jpg

After, with offending setting lever spring:

post-148-0-78800500-1411506765_thumb.jpg

In other news, I finally got a water-damaged rescue puppy of an omega 751 running very sweetly. I just need to find a dial...maybe...

post-148-0-18380900-1411506913_thumb.jpg

  • Like 1
Link to comment
Share on other sites
  • 5 months later...
mwilkes WRT Addict

mwilkes

Posted
  • Author
Posted (edited)

Just looking back through my older posts. I finally finished my water-damaged Omega last week. New dial, new hands, new barrel, new barrel bridge, new barrel arbor, and loads of keyless work bits. It runs incredibly well despite the hard life it's had, and it has become my favourite watch.

 

 

post-148-0-94917500-1425384807_thumb.jpg

Edited by mwilkes
  • Like 2
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • HectorLooi
      DIY centre seconds support base

      By HectorLooi · Posted

      I've been contemplating getting one of these for some time now, after working on a few spring loaded centre seconds pinion movements. It's not an absolutely necessary tool to have, hence the procrastination.  Then it hit me, all I need is a flat base with a screw in it. So I scrounged around for something suitable and ended up with this. This is some rubber thingy that is  supposed to stop furniture with casters from moving around. In fact, any flat material with sufficient thickness to hold the screw in the centre would do.  
    • Bonefixer
      Deciphering mainspring specifications…

      By Bonefixer · Posted

      I think your axes are mislabelled here. They need switching around. 
    • Roll1ex
      Rolex 3130/3135 Automatic winding issue

      By Roll1ex · Posted

      @clockboy Thank you for the response.
    • Roll1ex
      Rolex 3130/3135 Automatic winding issue

      By Roll1ex · Posted

      @Knebo Thank you for the detailed response and reminding me. I went back and introduced myself. That's really good information, for 15xx it should be similar. Will dig deeper into that.   Yes I mean that. Attaching some pictures. New to shooting through a loupe so pardon the quality. I don't quite get the strength point, could you elaborate? Seeing the punch used for the job, it should limit the highest point of the metal being pushed, Maybe a worn out punch?       I haven't checked the axle will do that, but thee watchmaker told me that the 9'o clock side has been over-polished and the caseback is sinking on that side which is causing the issue. Armed with this knowledge, I will investigate both. The Picture would certainly suggest that plus the Intense pitting (wrist perfuming habit of my family) might be contributing to how the caseback fits.      Thank you again, I have made a checklist and will be investigating all the points you mentioned.   Rolex told me that they will replace the dial and bracelet so I didn't go that route. Its an independent watchmaker, and a very well reputed one in online and offline collector circles. I have seen his work and got work done from him before, this is the first time something like this is coming up. Maybe he is getting lazy in sourcing good parts. lol.
    • Neverenoughwatches
      T shirt

      By Neverenoughwatches · Posted

      😞 I hate the heat, i work outside in winter in a t shirt . 
×
×
  • Create New...